549644
30
Zoom out
Zoom in
Previous page
1/124
Next page
30
ENGLISH
Charging the battery pack (fi g. A & B)
Always check the mains prior to charging the
battery pack. If the mains is functioning but the
battery pack does not charge, take your charger to
an authorized D E WALT repair agent. Whilst
charging, the charger and the battery pack may
become warm to touch. This is a normal condition
and does not indicate a problem.
@
Do not charge the battery pack at
ambient temperatures < 4 °C or > 40 °C.
Recommended charging temperature:
approx. 24 °C.
To charge the battery pack (10), insert it into the
charger (12) as shown and plug in the charger.
Be sure that the battery pack is fully seated in
the charger. The red charging indicators (13)
will blink according to the state of charge of the
battery pack.
When fi nished charging, the indicators are all
on. The charger automatically switches to
equalise mode.
The battery pack can be removed at any time or
left in the connected charger indefi nitely.
The red charging indicators fl ash rapidly to
indicate a charging problem. Reinsert the
battery pack or try a new one. If the new pack
also refuses to charge, have your charger
tested by an authorized D E WALT repair agent.
The red charging indicators fl ash rapidly with
one short blink followed by a long blink to
indicate a problem with the charger. Return the
charger to an authorized D E WALT repair agent.
When plugged into power sources such as
generators or sources that convert DC to AC,
the red charging indicators (13) may fl ash
together with two fast blinks followed by a
pause. This indicates a temporary problem of
the power source. The charger will
automatically switch back to normal operation.
Charging process (fi g. B)
Refer the table below for the state of charge of the
battery pack.
State of charge
1 light blinkling < 33%
1 light blinkling, 1 light on 33-66%
1 light blinkling, 2 lights on 66-99%
3 lights on 100%
Automatic refresh
@
The automatic refresh mode will
equalize or balance the individual
cells in the battery pack at its peak
capacity. Battery packs should be
refreshed weekly or whenever the
pack no longer delivers the same
amount of work.
To refresh your battery pack, place the battery
in the charger as usual. Leave the battery pack
for at least 8 hours in the charger.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot
or too cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery has
reached an appropriate temperature. The charger
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
Deep discharge protection
The battery pack is protected against deep
discharging when it is used in the tool.
Inserting and removing bits (fi g. A & C)
Open the chuck by turning the sleeve (15)
counterclockwise and insert the bit shank.
Place the bit in the chuck as far as it will go and
lift slightly before tightening.
Tighten fi rmly by turning the sleeve clockwise.
To remove the bit, proceed in reverse order.
Selecting the operating mode (fi g. D)
The tool can be used in the following operating
modes:
- Screwdriving
- Rotary drilling: for steel, wood and plastics
- Percussion drilling: for masonry
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DC900KL T 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC900KL T 1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info