Manual DeWalt DC832 T 10 (page 41 of 184) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

550301

Zoom out

Zoom in

1/184

ENGLISH

Forward/Reverse Control Button

(ﬁ g. 1)

A forward/reverse control button (b) determines the

direction of the tool and also serves as a lock off

button.

To select forward rotation, release the trigger

switch and depress the forward/reverse control

button on the right side of the tool.

To select reverse, depress the forward/reverse

control button on the left side of the tool.

The center position of the control button locks the

tool in the OFF position. When changing the position

of the control button, be sure the trigger is released.

NOTE: The first time the tool is run after changing

the direction of rotation, you may hear a click on

start up. This is normal and does not indicate a

problem.

Worklight (ﬁ g. 1)

There is a worklight (g) located just above the trigger

switch (a). The worklight will be activated when the

trigger switch is squeezed.

NOTE: The worklight is for lighting the immediate

work surface and is not intended to be used as a

flashlight.

Quick-Release Chuck (ﬁ g. 4)

DC825, DC827, DC835, DC837, DC845

NOTE: The chuck accepts 1/4" hex accessories

only.

Place the switch in the locked off (center) position or

remove battery pack before changing accessories.

To install an accessory, pull the chuck collar (c)

away from the front of the tool, insert the accessory

and release the collar. The accessory is locked in

place.

To remove an accessory, pull the chuck collar

away from the front of the tool. Remove the

accessory and release the collar.

Anvil With Detent Pin (ﬁ g. 5)

DC820, DC822, DC830, DC832, DC840

Place the switch in the locked off (center) position or

remove battery pack before changing accessories.

To install a socket on the anvil, align the hole in

the side of the socket with the detent pin (e) on the

anvil (f). Press the socket on until the detent pin

engages in the hole. Depression of detent pin may

be necessary to aid installation of socket.

CAUTION: Use only impact sockets.

Non-impact sockets may break and

cause a hazardous condition. Inspect

sock et prior to use to ensure that it

con tains no cracks.

To remove a socket, depress the detent pin

through the hole and pull the socket off.

Usage

Your impact tool generates the following output

torque:

Cat # Ft.-Lbs. In.-Lbs. Nm

DC820 145 1740 195

DC822 145 1740 195

DC825 111 1330 150

DC827 111 1330 150

DC830 135 1620 180

DC832 135 1620 180

DC835 103 1240 140

DC837 103 1240 140

DC840 120 1440 160

DC845 96 1150 130

CAUTION: Ensure fastener and/or

system will withstand the level of torque

generated by the tool. Excessive torque

may cause breakage and possible

personal injury.

1. Place the socket on the fastener head. Keep

the tool pointed straight at the fastener.

2. Press switch to start operation. Always check

torque with a torque wrench, as the fastening

torque is affected by many factors including the

following:

• Voltage: Low voltage, due to a nearly

discharged battery, will reduce fastening

torque.

• Socket size: Failure to use the correct

socket size will cause a reduction in fastening

torque.

• Bolt Size: Larger bolt diameters generally

require higher fastening torque. Fastening

torque will also vary according to length,

grade, and torque coefficient.

• Bolt: Ensure that all threads are free of rust

and other debris to allow proper fastening

torque

• Material: The type of material and surface

finish of the material will affect fastening

torque.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC832 T 10 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 4,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DC832 T 10

DeWalt DC832 T 10 Additional guide - English - 20 pages

DeWalt DC832 T 10 Additional guide - Polish - 24 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DC832 T 10 Manual

Product: