Manual DeWalt DC757K T 10 (page 26 of 108) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

549074

Zoom out

Zoom in

1/108

ENGLISH

• Take off the protective cap (13) before placing

the battery pack (9) in the charger or tool.

• Place the protective cap over the contacts

immediately after removing the battery pack from

the charger or tool.

Make sure the protective cap is in place

before storing or carrying a detached

battery pack.

Equalisation mode

The equalisation mode helps to maintain the

optimum capacity of the battery pack. It is therefore

recommended to use the equalisation mode weekly

or every 10 charge/discharge cycles.

• Charge the battery pack as described above.

• When the charging indicator stops blinking, leave

the battery in the charger for approx. 4 hours.

DE9116 - Hot Pack Delay

When the charger detects a battery that is hot,

it automatically starts a Hot Pack Delay, suspending

charging until the battery has cooled. After the

battery has cooled, the charger automatically

switches to the pack charging mode. This feature

ensures maximum battery life. The red indicator (12)

blinks long, then short while in the Hot Pack Delay

mode.

Inserting and removing bits (fig. A & C)

• Open the chuck by turning the sleeve (14)

counterclockwise and insert the bit shank.

• Place the bit in the chuck as far as it will go and

lift slightly before tightening.

• Tighten firmly by turning the sleeve clockwise.

• To remove the bit, proceed in reverse order.

Selecting the operating mode or adjusting the

torque (fig. D)

The collar of this tool has 17 positions for the

adjustment of the torque to suit the size of the screw

and the workpiece material. For torque adjustment,

refer to the section «Screwdriving».

• Select the drilling mode or torque by aligning the

symbol or number on the collar (4) with the

indicator (15) on the housing.

Forward/reverse slider (fig. E)

• To select forward or reverse rotation, use the

forward/reverse slider (2) as shown (see arrows

on tool).

Always wait until the motor has come to

a complete standstill before changing the

direction of rotation.

Two gear selector (fig. F)

Your tool is fitted with a two gear selector (3) to vary

the speed/torque ratio.

1 low speed/high torque

(drilling large holes, driving screws)

2 high speed/low torque

(drilling smaller holes)

For speed rates, refer to the technical data.

Always push the two gear selector

completely forward or backward.

• Do not change gears at full speed or during use.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool.

Switching on and off (fig. A & E)

• To run the tool, press the variable speed switch

(1). The pressure exerted on the variable speed

switch determines the tool speed.

• To stop the tool, release the switch.

• To lock the tool in the off position, move the

forward/reverse slider (2) to the central position.

The drill is equipped with a brake to stop

the tool as soon as the variable speed

switch is fully released.

Screwdriving (fig. A)

• Select forward or reverse rotation using the slider

(2).

• Set the collar (4) to position 1 and begin

screwdriving (low torque).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC757K T 10 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 0,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DC757K T 10

DeWalt DC757K T 10 Additional guide - English - 20 pages

DeWalt DC757K T 10 Additional guide - Polish - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DC757K T 10 Manual

Product: