Manual DeWalt DC757 T 10 (page 25 of 108) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

549170

Zoom out

Zoom in

1/108

ENGLISH

Your DEWALT charger is double

insulated in accordance with EN 60335.

Mains plug replacement

(U.K. & Ireland only)

• Should your mains plug need replacing and you

are competent to do this, proceed as instructed

below. If you are in doubt, contact an authorized

DEWALT repair agent or a qualified electrician.

• Disconnect the plug from the supply.

• Cut off the plug and dispose of it safely; a plug

with bared copper conductors is dangerous if

engaged in a live socket outlet.

• Only fit 13 Amperes BS1363A approved plugs

fitted with the correctly rated fuse (1).

• The cable wire colours, or a letter, will be marked

at the connection points of most good quality

plugs. Attach the wires to their respective points

in the plug (see below). Brown is for Live (L) (2)

and Blue is for Neutral (N) (4).

• Before replacing the top cover of the mains plug

ensure that the cable restraint (3) is holding the

outer sheath of the cable firmly and that the two

leads are correctly fixed at the terminal screws.

Never use a light socket.

Never connect the live (L) or neutral (N)

wires to the earth pin marked E or .

Using an extension cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of your charger

(see technical data).

The minimum conductor size is 1 mm

;

the maximum length is 30 m.

Assembly and adjustment

• Prior to assembly and adjustment,

always remove the battery pack.

• Always switch off the tool before

inserting or removing the battery pack.

• Use only DEWALT battery packs and

chargers.

Battery pack (fig. A & B)

Charging the battery pack

• To charge the battery pack (9), insert it into the

charger (11) as shown and plug in the charger.

Be sure that the battery pack is fully seated in the

charger, but do not force it.

The red charging indicator (12) will blink. After

approx. 1 hour, it will stop blinking and remain on.

The battery pack is now fully charged and the

charger automatically switches to equalisation mode.

After approx. 4 hours, it will switch to maintenance

charge mode. The battery pack can be removed at

any time or left in the connected charger indefinitely.

• The red charging indicator flashes rapidly to

indicate a charging problem. Reinsert the battery

pack or try a new one. If the new pack also

refuses to charge, have your charger tested by

an authorised DEWALT repair agent.

• When plugged into power sources such as

generators or sources that convert DC to AC,

the red charging indicator may blink twice, switch

off and repeat. This indicates a temporary

problem of the power source. The charger will

automatically switch back to normal operation.

Do not charge the battery pack at

ambient temperatures < 4 °C or > 40 °C.

Recommended charging temperature:

approx. 24 °C.

Inserting and removing the battery pack

• Insert the battery pack into the grip (8) until it

clicks in place.

• To remove the battery pack, press the two

release buttons (10) simultaneously and pull the

pack out of the grip (8).

Battery cap (fig. B)

A protective cap is supplied to cover the contacts of

a detached battery pack. Without the protective cap

in place, loose metal objects could short circuit the

contacts, causing a fire hazard and damaging the

battery pack.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC757 T 10 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 0,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DC757 T 10

DeWalt DC757 T 10 Additional guide - English - 20 pages

DeWalt DC757 T 10 Additional guide - Polish - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DC757 T 10 Manual

Product: