549075
14
Zoom out
Zoom in
Previous page
1/20
Next page
12
Use only DEWALT battery packs and
chargers.
Inserting and Removing the
Battery Pack from the Tool (fi g. A)
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up can
cause injury.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the base of the tool with the notch inside
the tool’s handle.
2. Slide the battery pack firmly into the handle until
you hear the lock snap into place.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the release buttons (10) and firmly pull the
battery pack out of the tool handle.
2. Insert battery pack into the charger as described
in the charger section of this manual.
Inserting and Removing Bits (fi g. A & C)
Open the chuck by turning the sleeve (14)
counterclockwise and insert the bit shank.
Place the bit in the chuck as far as it will go and lift
slightly before tightening.
Tighten firmly by turning the sleeve clockwise.
To remove the bit, proceed in reverse order.
Selecting the Operating Mode or Adjusting the
Torque (fi g. D)
The collar of this tool has 17 positions for the
adjustment of the torque to suit the size of the screw
and the workpiece material. For torque adjustment,
refer to the section "Screwdriving".
Select the drilling mode or torque by aligning
the symbol or number on the collar (4) with the
indicator on the housing.
Forward/reverse Slider (fi g. E)
To select forward or reverse rotation, use the
forward/reverse slider (2) as shown (see arrows on
tool).
WARNING:
Always wait until the motor
has come to a complete standstill before
changing the direction of rotation.
Two Gear Selector (fi g. F)
Your tool is fitted with a two gear selector (3) to vary
the speed/torque ratio.
ENGLISH
1 low speed/high torque
(drilling large holes, driving screws)
2 high speed/low torque
(drilling smaller holes)
For speed rates, refer to the technical data.
WARNING:
Always push the two gear selector
completely forward or backward.
Do not change gears at full speed or
during use.
OPERATION
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
Instructions for Use
WARNING:
Always observe the safety instructions
and applicable regulations.
Be aware of the location of pipework
and wiring.
Apply only a gentle pressure to the tool.
Proper Hand Position (fi g. A, G)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper
hand position as shown.
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on top of the
housing, with the other hand on the grip (8).
Switching On and Off (fi g. A & E)
To run the tool, press the variable speed switch (1).
The pressure exerted on the variable speed switch
determines the tool speed.
To stop the tool, release the switch.
To lock the tool in the off position, move the
forward/reverse slider (2) to the central position.
WARNING:
The drill is equipped with
a brake to stop the tool as soon as the
variable speed switch is fully released.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DC756 T 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC756 T 10 in the language / languages: English as an attachment in your email.

The manual is 0,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DC756 T 10

DeWalt DC756 T 10 User Manual - English, German, Dutch, Danish, French, Italian - 108 pages

DeWalt DC756 T 10 Additional guide - Polish - 16 pages

DeWalt DC756 T 10 User Manual - Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian, Finnish - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info