549653

DeWalt DC750 T 3-EU Manual

14
Zoom out
Zoom in
Previous page
1/20
Next page
ENGLISH
12
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the base of the tool with the notch inside
the tool’s handle (fig. 2).
2. Slide the battery pack firmly into the handle until
you hear the lock snap into place.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the release buttons (j) and firmly pull the
battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
INSERTING AND REMOVING BITS (FIG. 1, 4)
1. Open the chuck by turning the sleeve (p)
counterclockwise and insert the bit shank.
2. Place the bit in the chuck as far as it will go and
lift slightly before tightening.
3. Tighten firmly by turning the sleeve clockwise.
4. To remove the bit, proceed in reverse order.
SELECTING THE OPERATING MODE OR ADJUSTING THE
TORQUE (FIG. 5)
The collar of this tool has 15 positions for the
adjustment of the torque to suit the size of the screw
and the workpiece material. For torque adjustment,
refer to Screwdriving.
Select the drilling mode or torque by aligning the
symbol or number on the collar (e) with the indicator
(q) on the housing.
FORWARD/REVERSE SLIDER (FIG. 6)
To select forward or reverse rotation, use the
forward/ reverse slider (b) as shown (see arrows on
tool).
WARNING: To reduce the risk of
personal injury, always wait until the
motor has come to a complete standstill
before changing the direction of rotation.
TWO-GEAR SELECTOR (FIG. 7)
Your tool is fitted with a two-gear selector (f) to vary
the speed/torque ratio.
1 low speed/high torque
(drilling large holes, driving screws)
2 high speed/low torque
(drilling smaller holes)
For speed rates, refer to the Technical Data.
WARNING: To reduce the risk of
personal injury:
• Always push the two gear selector
completely forward or backward.
• Do not change gears at full speed or
during use.
Removing and Fitting the Chuck
(fi g. 8, 9)
DW907
1. Open the chuck jaws as far as possible.
2. Insert a screwdriver into the chuck and remove
the chuck retaining screw by turning clockwise
as shown in figure 8.
3. Tighten an hex key into the chuck and strike it
with a hammer as shown in figure 9. This will
loosen the chuck so that it can be unscrewed
by hand.
4. To refit the chuck, proceed in reverse order.
Prior to Operation
1. Make sure your battery pack is (fully) charged.
2. Insert the appropriate bit.
3. Mark the spot where the hole is to be drilled.
4. Select forward or reverse rotation.
OPERATION
Instructions for Use
WARNING: To reduce the risk of
personal injury:
• Always observe the safety instructions
and applicable regulations.
• Be aware of the location of pipework
and wiring.
• Apply only a gentle pressure to
the tool. Excessive force does not
speed up drilling but decreases tool
performance and may shorten tool life.
• To minimise stalling on break-through,
progressively reduce the drill point
pressure towards the end of the
operation.
• Keep the motor running when pulling
the bit back out of a drilled hole. This
will help prevent jamming.
Proper Hand Position (fi g. 1, 10)
WARNING: To reduce the risk of
serious personal injury, ALWAYS
use proper hand position as shown
in figure 10.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DC750 T 3-EU at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC750 T 3-EU in the language / languages: English as an attachment in your email.

The manual is 0,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DC750 T 3-EU

DeWalt DC750 T 3-EU User Manual - English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish - 176 pages

DeWalt DC750 T 3-EU Additional guide - Turkish - 34 pages

DeWalt DC750 T 3-EU User Manual - Turkish, Spanish, Norwegian, Finnish - 176 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info