549073
10
Zoom out
Zoom in
Previous page
1/20
Next page
ENGLISH
8
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual
before use.
DATE CODE POSITION
The Date Code, which also includes the year of
manufacture, is printed into the housing surface that
forms the mounting joint between tool and battery!
Example:
2009 XX XX
Year of Manufacture
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual
contains important safety and operating instruc-
tions for the DE9130, DE9135 and DE9116 battery
chargers.
Before using charger, read all instructions and
cautionary markings on charger, battery pack,
and product using battery pack.
DANGER: Electrocution hazard. 230
volts are present at charging terminals.
Do not probe with conductive objects.
Electric shock or electrocution may
result.
WARNING: Shock hazard. Do not allow
any liquid to get inside charger. Electric
shock may result.
CAUTION: Burn hazard. To reduce
the risk of injury, charge only DEWALT
rechargeable batteries. Other types of
batteries may burst causing personal
injury and damage.
CAUTION: Under certain conditions,
with the charger plugged in to the
power supply, the exposed charging
contacts inside the charger can be
shorted by foreign material. Foreign
materials of a conductive nature such
as, but not limited to, steel wool,
aluminum foil, or any buildup of metallic
particles should be kept away from
charger cavities. Always unplug the
charger from the power supply when
there is no battery pack in the cavity.
Unplug charger before attempting to
clean.
DO NOT attempt to charge the battery pack
with any chargers other than the ones in
this manual. The charger and battery pack are
specifically designed to work together.
These chargers are not intended for
any uses other than charging DEWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock or
electrocution.
Do not expose charger to rain or snow.
Pull by plug rather than cord when
disconnecting charger. This will reduce risk of
damage to electric plug and cord.
Make sure that cord is located so that it
will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
Do not use an extension cord unless it
is absolutely necessary. Use of improper
extension cord could result in risk of fire, electric
shock, or electrocution.
An extension cord must have adequate wire
size (AWG or American Wire Gauge) for
safety. The smaller the gauge number of the
wire, the greater the capacity of the cable, that
is 16 gauge has more capacity than 18 gauge.
When using more than one extension to make
up the total length, be sure each individual
extension contains at least the minimum wire
size.
Do not place any object on top of charger
or place the charger on a soft surface that
might block the ventilation slots and result
in excessive internal heat. Place the charger
in a position away from any heat source. The
charger is ventilated through slots in the top and
the bottom of the housing.
Do not operate charger with damaged cord
or plug — have them replaced immediately.
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in
any way. Take it to an authorized service center.
Do not disassemble charger; take it to an
authorized service center when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock, electrocution or
fire.
Disconnect the charger from the outlet
before attempting any cleaning. This will
reduce the risk of electric shock. Removing
the battery pack will not reduce this risk.
• NEVER attempt to connect 2 chargers together.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DC743K T 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC743K T 10 in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DC743K T 10

DeWalt DC743K T 10 User Manual - English, German, Dutch, Danish, French, Italian - 204 pages

DeWalt DC743K T 10 Additional guide - Polish - 24 pages

DeWalt DC743K T 10 User Manual - Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian, Finnish - 204 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info