Manual DeWalt DC740 T 3 (page 40 of 172) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

549069

Zoom out

Zoom in

1/172

ENGLISH

3. To lock the tool in the off position, move the

forward/reverse slider (b) to the central position.

WARNING: To reduce the risk of

personal injury the drill is equipped with

a brake to stop the tool as soon as the

variable speed switch is fully released.

Drill Operation

1. Select the desired speed/torque range using the

gear shifter to match the speed and torque to

the planned operation.

2. For WOOD, use twist bits, spade bits, power

auger bits or hole saws. For METAL, use high-

speed steel twist drill bits or hole saws. Use

a cutting lubricant when drilling metals. The

exceptions are cast iron and brass which should

be drilled dry.

3. Always apply pressure in a straight line with the

bit. Use enough pressure to keep the drill bit

biting, but do not push hard enough to stall the

motor or deflect the bit.

4. Hold tool firmly with both hands to control the

twisting action of the drill.

5. IF DRILL STALLS, it is usually because it

is being overloaded. RELEASE TRIGGER

IMMEDIATELY, remove drill bit from work, and

determine cause of stalling. DO NOT CLICK

TRIGGER OFF AND ON IN AN ATTEMPT

TO START A STALLED DRILL – THIS CAN

DAMAGE THE DRILL.

6. Keep the motor running when pulling the bit

back out of a drilled hole. This will help prevent

jamming.

SCREWDRIVING (FIG. 1)

1. Select forward or reverse rotation using the

slider (b). Match the speed and torque to the

planned operation. Insert the desired fastener

accessory into the chuck as you would any drill

bit.

2. Set the collar (d) to position 1 and begin

screwdriving (low torque). Make a few practice

runs in scrap or unseen areas to determine the

proper position of the clutch collar.

3. If the clutch ratchets too soon, adjust the collar

to increase the torque as required.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

serious personal injury, turn tool off

and disconnect battery pack before

making any adjustments or removing/

installing attachments or accessories.

An accidental start-up can cause injury.

The charger is not serviceable. There are no

serviceable parts inside the charger.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

tool; never immerse any part of the tool

into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect

the charger from the AC outlet before

cleaning. Dirt and grease may be

removed from the exterior of the charger

using a cloth or soft non-metallic brush.

Do not use water or any cleaning

solutions.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC740 T 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 3,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DC740 T 3

DeWalt DC740 T 3 Additional guide - English - 20 pages

DeWalt DC740 T 3 Additional guide - Polish - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DC740 T 3 Manual

Product: