549162

DeWalt DC733C T 1 Manual

15
Zoom out
Zoom in
Previous page
1/20
Next page
ENGLISH
13
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on top of
the housing, with the other hand on the grip (h).
SWITCHING ON AND OFF (FIG. 1, 6)
1. To run the tool, press the variable speed switch
(a). The pressure exerted on the variable speed
switch determines the tool speed.
2. To stop the tool, release the switch.
3. To lock the tool in the off position, move the
forward/reverse slider (b) to the central position.
WARNING: To reduce the risk of
personal injury the drill is equipped with
a brake to stop the tool as soon as the
variable speed switch is fully released.
Drill Operation
1. Select the desired speed/torque range using the
gear shifter to match the speed and torque to
the planned operation.
2. For WOOD, use twist bits, spade bits, power
auger bits or hole saws. For METAL, use high-
speed steel twist drill bits or hole saws. Use
a cutting lubricant when drilling metals. The
exceptions are cast iron and brass which should
be drilled dry.
3. Always apply pressure in a straight line with the
bit. Use enough pressure to keep the drill bit
biting, but do not push hard enough to stall the
motor or deflect the bit.
4. Hold tool firmly with both hands to control the
twisting action of the drill.
5. IF DRILL STALLS, it is usually because it
is being overloaded. RELEASE TRIGGER
IMMEDIATELY, remove drill bit from work, and
determine cause of stalling. DO NOT CLICK
TRIGGER OFF AND ON IN AN ATTEMPT
TO START A STALLED DRILL – THIS CAN
DAMAGE THE DRILL.
6. Keep the motor running when pulling the bit
back out of a drilled hole. This will help prevent
jamming.
SCREWDRIVING (FIG. 1)
1. Select forward or reverse rotation using the
slider(b). Match the speed and torque to the
planned operation. Insert the desired fastener
accessory into the chuck as you would any drill
bit.
2. Set the collar (d) to position 1 and begin
screwdriving (low torque). Make a few practice
runs in scrap or unseen areas to determine the
proper position of the clutch collar.
3. If the clutch ratchets too soon, adjust the collar
to increase the torque as required.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
serious personal injury, turn tool off
and disconnect battery pack before
making any adjustments or removing/
installing attachments or accessories.
An accidental start-up can cause injury.
The charger is not serviceable. There are no
serviceable parts inside the charger.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DC733C T 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC733C T 1 in the language / languages: English as an attachment in your email.

The manual is 0,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DC733C T 1

DeWalt DC733C T 1 User Manual - English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 176 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info