446578
26
Zoom out
Zoom in
Previous page
1/108
Next page
26
ENGLISH
Take off the protective cap (13) before placing
the battery pack (9) in the charger or tool.
Place the protective cap over the contacts
immediately after removing the battery pack from
the charger or tool.
Make sure the protective cap is in place
before storing or carrying a detached
battery pack.
Equalisation mode
The equalisation mode helps to maintain the
optimum capacity of the battery pack. It is therefore
recommended to use the equalisation mode weekly
or every 10 charge/discharge cycles.
Charge the battery pack as described above.
When the charging indicator stops blinking, leave
the battery in the charger for approx. 4 hours.
DE9116 - Hot Pack Delay
When the charger detects a battery that is hot,
it automatically starts a Hot Pack Delay, suspending
charging until the battery has cooled. After the
battery has cooled, the charger automatically
switches to the pack charging mode. This feature
ensures maximum battery life. The red indicator (12)
blinks long, then short while in the Hot Pack Delay
mode.
Inserting and removing bits (fig. A & C)
Open the chuck by turning the sleeve (14)
counterclockwise and insert the bit shank.
Place the bit in the chuck as far as it will go and
lift slightly before tightening.
Tighten firmly by turning the sleeve clockwise.
To remove the bit, proceed in reverse order.
Selecting the operating mode or adjusting the
torque (fig. D)
The collar of this tool has 17 positions for the
adjustment of the torque to suit the size of the screw
and the workpiece material. For torque adjustment,
refer to the section «Screwdriving».
Select the drilling mode or torque by aligning the
symbol or number on the collar (4) with the
indicator (15) on the housing.
Forward/reverse slider (fig. E)
To select forward or reverse rotation, use the
forward/reverse slider (2) as shown (see arrows
on tool).
Always wait until the motor has come to
a complete standstill before changing the
direction of rotation.
Two gear selector (fig. F)
Your tool is fitted with a two gear selector (3) to vary
the speed/torque ratio.
1 low speed/high torque
(drilling large holes, driving screws)
2 high speed/low torque
(drilling smaller holes)
For speed rates, refer to the technical data.
Always push the two gear selector
completely forward or backward.
Do not change gears at full speed or during use.
Instructions for use
Always observe the safety instructions
and applicable regulations.
Be aware of the location of pipework and
wiring.
Apply only a gentle pressure to the tool.
Switching on and off (fig. A & E)
To run the tool, press the variable speed switch
(1). The pressure exerted on the variable speed
switch determines the tool speed.
To stop the tool, release the switch.
To lock the tool in the off position, move the
forward/reverse slider (2) to the central position.
The drill is equipped with a brake to stop
the tool as soon as the variable speed
switch is fully released.
Screwdriving (fig. A)
Select forward or reverse rotation using the slider
(2).
Set the collar (4) to position 1 and begin
screwdriving (low torque).
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DC727 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC727 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 0,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DC727

DeWalt DC727 User Manual - English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian, Finnish - 204 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info