Manual DeWalt DC542K (page 38 of 176) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546910

Zoom out

Zoom in

1/176

english

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the battery pack

voltage corresponds to the voltage on the rating

plate. Also make sure that the voltage of your

charger corresponds to that of your mains.

Your DeWA LT charger is double insulated

in accordance with EN 60335.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

eWALT service organization.

Mains Plug Replacement

(U.K. & Ireland Only)

DANGER:

 • Shouldyourmainsplugneedreplacingandyou

are competent to do this, proceed as instructed

below. If you are in doubt, contact an authorized

DeWALT repair agent or a qualified electrician.

 • Disconnecttheplugfromthesupply.

 • Cutoffthepluganddisposeofitsafely;aplug

with bared copper conductors is dangerous if

engaged in a live socket outlet.

 • Onlyfit13AmperesBS1363Aapprovedplugs

fitted with the correctly rated fuse (1).

 • Thecablewirecolours,oraletter,willbe

marked at the connection points of most good

quality plugs. Attach the wires to their respective

points in the plug (see below). Brown is for Live

(L) (2) and Blue is for Neutral (N) (4).

 • Beforereplacingthetopcoverofthemainsplug

ensure that the cable restraint (3) is holding the

outer sheath of the cable firmly and that the two

leads are correctly fixed at the terminals crews.

WARNING: NEVER use a light socket.

NEVER connect the live (L) or

neutral (N) wires to the earth

pin marked E or

Using an Extension Cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of your charger

(see technical data). The minimum conductor size is

1 mm

; the maximum length is 30 m.

Assembly and Adjustment

WARNING: Prior to assembly and

adjustment, always remove the battery

pack. Always switch off the tool before

inserting or removing the battery pack.

WARNING: Use only DeWALT battery

packs and chargers.

Inserting and Removing the

Battery Pack

1. Insert the battery pack (d) into the grip until it

clicks in place.

2. To remove the battery pack, press the two

release buttons (i) simultaneously and pull the

pack out of the grip.

Electronic Force Control

The tool is designed to dispense a wide range of

adhesive and caulk, and to detect when material is

not dispensing or dispensing slowly. Reasons the

tool may not dispense material properly may be

solidified adhesive, puncture holes, frozen materials

and the like. In such cases, the integrated electronic

force control module will shut the tool down.

Always follow the manufacturer’s recommendations

regarding solidified adhesive, puncture holes, frozen

materials, etc., to reduce the risk of damaging the

tube or casing.

Remove the battery pack and replace material tube/

casing following the manufacturer’s instructions and

the instructions under To Insert Material. Take the

tool to a DeWALT service center if the tool continues

to shut down.

Constant Speed

The constant speed feature allows the material to

flow at the same rate of speed, regardless of the

variable speed setting or the amount of material in

the cartridge.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC542K in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DC542K Manual

Product: