Manual DeWalt dc411n xj 18v 4 1 2 angle grinder bare (page 50 of 264) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

391260

Zoom out

Zoom in

1/264

ENGLISH

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when

disconnecting charger. This will reduce risk

of damage to electric plug and cord.

• Make sure that cord is located so that it

will not be stepped on, tripped over, or

otherwise subjected to damage or stress.

• Do not use an extension cord unless it

is absolutely necessary. Use of improper

extension cord could result in risk of fire,

electric shock, or electrocution.

• Do not place any object on top of charger

or place the charger on a soft surface that

might block the ventilation slots and result

in excessive internal heat. Place the charger

in a position away from any heat source. The

charger is ventilated through slots in the top and

the bottom of the housing.

• Do not operate charger with damaged cord

or plug — have them replaced immediately.

• Do not operate charger if it has received

a sharp blow, been dropped, or otherwise

damaged in any way. Take it to an authorised

service centre.

• Do not disassemble charger; take it to an

authorised service centre when service or

repair is required. Incorrect reassembly may

result in a risk of electric shock, electrocution or

fire.

• Disconnect the charger from the outlet

before attempting any cleaning. This will

reduce the risk of electric shock. Removing

the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on

standard 230V household electrical power.

Do not attempt to use it on any other

voltage. This does not apply to the vehicular

charger.

SAVE THESE INSTRUCTIONS

Chargers

The DE9116 charger accepts 7.2 – 18 V NiCd and

NiMH batteries.

The DE9135 charger accepts 7.2 – 18 V NiCd,

NiMH or Li-Ion batteries.

These chargers require no adjustment and are

designed to be as easy as possible to operate.

Charging Procedure (Fig. 2)

DANGER: Electrocution hazard.

230 volts present at charging terminals.

Do not probe with conductive objects.

Danger of electric shock or

electrocution.

1. Plug the charger (j) into an appropriate outlet

before inserting battery pack.

2. Insert the battery pack into the charger. The red

(charging) light will blink continuously indicating

that the charging process has started.

3. The completion of charge will be indicated by

the red light remaining ON continuously. The

pack is fully charged and may be used at this

time or left in the charger.

NOTE: To ensure maximum performance and life of

NiCd, NiMH and Li-Ion batteries, charge the battery

for a minimum of 10 hours before first use.

Charging Process

Refer the table below for the state of charge of the

battery pack.

State of charge

charging – – – –

fully charged –––––––––––

hot/cold pack delay –– – –– –

replace battery pack •••••••••••

problem •• •• •• ••

Automatic Refresh

The automatic refresh mode will equalise or balance

the individual cells in the battery pack at its peak

capacity. Battery packs should be refreshed weekly

or whenever the pack no longer delivers the same

amount of work.

To refresh your battery pack, place the battery in the

charger as usual. Leave the battery pack for at least

10 hours in the charger.

Hot/Cold Pack Delay

When the charger detects a battery that is too hot

or too cold, it automatically starts a Hot/Cold Pack

Delay, suspending charging until the battery has

reached an appropriate temperature. The charger

then automatically switches to the pack charging

mode. This feature ensures maximum battery life.

LI-ION BATTERY PACKS ONLY

Li-Ion batteries are designed with an Electronic

Protection System that will protect the battery

against overloading, overheating or deep discharge.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dc411n xj 18v 4 1 2 angle grinder bare in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 26,54 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt dc411n xj 18v 4 1 2 angle grinder bare Manual

Product: