446529

DeWalt DC222 Manual

41
Zoom out
Zoom in
Previous page
1/188
Next page
ENGLISH
39
2. Insert battery pack into the charger as
described in the charger section of this manual.
Selecting the Operating Mode
(fig. 3A, 3B)
DC222 (FIG. 3A)
The tool can be used in the following operating
modes:
Rotary drilling: for screwdriving and for
drilling into steel, wood and plastics
Hammer drilling: for concrete and
masonry drilling operations.
DC223, DC224 (FIG. 3B)
The tool can be used in the following operating
modes:
Rotary drilling: for screwdriving and for
drilling into steel, wood and plastics
Hammer drilling: for concrete and
masonry drilling operations.
Hammering only: for light chipping.
1. To select the operating mode, press the safety
lock (d) and rotate the mode selector switch
(c) until it points to the symbol of the required
mode.
2. Release the safety lock and check that the
mode selector switch is locked in place.
WARNING: Do not select the operating
mode when the tool is running.
Inserting and Removing SDS Plus
®
Accessories (fig. 4)
This tool uses SDS Plus
®
accessories (refer to the
inset in fig. 4 for a cross-section of an SDS Plus
®
bit
shank).
1. Clean and grease the bit shank.
2. Insert the bit shank into the tool holder (e).
3. Push the bit down and turn it slightly until it fits
into the slots.
4. Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be
able to move axially several centimetres when
locked in the tool holder.
5. To remove a bit pull back the tool holder locking
sleeve (o) and pull out the bit.
WARNING: Always wear gloves when
you change accessories. The exposed
metal parts on the tool and accessory
may become extremly hot during
operation.
Fitting the Side Handle (fig. 1)
The side handle (i) can be fitted to suit both RH- and
LH-users.
WARNING: Do not use the tool without
the side handle properly assembled.
1. Loosen the side handle.
2. For RH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the
left.
3. For LH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the
right.
4. Rotate the side handle to the desired position
and tighten the handle.
Setting the Drilling Depth (fi g. 5)
1. Insert the required drill bit.
2. Slacken the side handle (i).
3. Fit the depth adjustment rod (h) through the
hole in the side handle clamp.
4. Adjust the drilling depth as shown.
5. Tighten the side handle.
Forward/reverse Slider (fig. 6)
1. Push the forward/reverse slider (b) to the
LH-side for forward (RH) rotation. See arrows
on tool.
2. Push the forward/reverse slider (b) to the
RH-side for reverse (LH) rotation.
WARNING: Always wait until the motor
has come to a complete standstill
before changing the direction of rotation.
Replacing the Tool Holder with the
Chuck (fig. 7)
DC224
1. Turn the locking collar (f) into the unlocking
position and pull the tool holder (e) off.
2. Push the chuck (p) onto the spindle and turn
the locking collar into the locking position.
3. To replace the chuck with the tool holder, first
remove the chuck the same way as the tool
holder was removed. Then place the tool holder
the same way as the chuck was placed.
… 41 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DC222 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC222 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 10,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info