Manual DeWalt DC 945 (page 31 of 132) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

78849

Zoom out

Zoom in

1/132

ENGLISH

● If the pack is left in the charger after the initial

charge, the charger will automatically initiate

the refresh mode. This mode will continue up to

8 hours, but the battery pack can be removed at

any time during the refresh mode.

Hot/Cold Pack Delay

When the charger detects a battery that is too hot

or too cold, it automatically starts a Hot/Cold Pack

Delay, suspending charging until the battery has

reached an appropriate temperature. The charger

then automatically switches to the pack charging

mode. This feature ensures maximum battery life.

The red indicator (13) blinks long, then short while

in the Hot/Cold Pack Delay mode.

Inserting and removing bits (ﬁ g. A & C)

● Open the chuck by turning the sleeve (15)

counterclockwise and insert the bit shank.

● Place the bit in the chuck as far as it will go and

lift slightly before tightening.

● Tighten ﬁ rmly by turning the sleeve clockwise.

● To remove the bit, proceed in reverse order.

Selecting the operating mode or adjusting the

torque (ﬁ g. D)

The collar of this tool has a wide range of positions

for the adjustment of the torque to suit the size of

the screw and the workpiece material. For torque

adjustment, refer to the section "Screwdriving".

● Select the drilling mode or torque by aligning

the symbol or number on the collar (4) with the

indicator (16) on the housing.

DC945/DC935/DC925

These tools can be used in the following operating

modes:

Rotary drilling: for steel, wood and

plastics

Percussion drilling: for masonry

Forward/reverse slider (ﬁ g. E)

● To select forward or reverse rotation, use the

forward/reverse slider (2) as shown (see arrows

on tool).

Always wait until the motor has come to

a complete standstill before changing

the direction of rotation.

Three-gear selector (ﬁ g. F)

Your tool is ﬁ tted with a three-gear selector (6) to

vary the speed/torque ratio.

1 low speed/high torque

2 medium speed/medium torque

3 high speed/low torque

For speed rates, refer to the technical data.

Do not change gears at full speed or

during use.

Instructions for use

● Always observe the safety instructions

and applicable regulations.

● Be aware of the location of pipework

and wiring.

● Apply only a gentle pressure to the tool.

Excessive force does not speed up

drilling but decreases tool performance

and may shorten tool life.

Prior to operation:

● Make sure your battery pack is (fully) charged.

● Make sure the battery pack is properly seated.

● Insert the appropriate bit.

● Mark the spot where the hole is to be drilled.

Switching on and off (ﬁ g. A & E)

● To run the tool, press the variable speed switch

(1). The pressure exerted on the variable speed

switch determines the tool speed.

● To stop the tool, release the switch.

● To lock the tool in the off position, move the

forward/reverse slider (2) to the central position.

Screwdriving (ﬁ g. A)

● Select forward or reverse rotation using the

slider (2).

● Set the collar (4) to position 1 and begin

screwdriving (low torque).

● If the clutch ratchets too soon, adjust the collar

to increase the torque as required.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC 945 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 1,69 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DC 945 Manual

Product: