79272

DeWalt DC 411 Manual

51
Zoom out
Zoom in
Previous page
1/220
Next page
ENGLISH
49
USING WIRE CUP BRUSHES AND WIRE WHEELS
Wire wheels and brushes can be used for removing
rust, scale and paint, and for smoothing irregular
surfaces.
1. Allow the tool to reach full speed before
touching the tool to the work surface.
2. Apply minimum pressure to work surface,
allowing the tool to operate at high speed.
Material removal rate is greatest when the tool
operates at high speed.
3. Maintain a 5˚ to 10˚ angle between
the tool and work surface for wire cup
brushes.
4. Maintain contact between the edge of the wheel
and the work surface with wire wheels.
5. Continuously move the tool in a forward and
back motion to avoid creating gouges in the
work surface. Allowing the tool to rest on the
work surface without moving, or moving the tool
in a circular motion causes burning and swirling
marks on the work surface.
6. Remove the tool from the work surface before
turning the tool off. Allow the tool to stop
rotating before setting it down.
CAUTION: Use extra care when
working over an edge, as a sudden
sharp movement of grinder may be
experienced.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
serious personal injury, turn tool off
and disconnect battery pack before
making any adjustments or removing/
installing attachments or accessories.
An accidental start-up can cause injury.
The charger is not serviceable. There are no
serviceable parts inside the charger.
Lubrication
This tool requires no lubrication.
CAUTION: Do not lubricate the tool as
it will damage the internal parts.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
using a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.
Optional accessories
WARNING: Since accessories, other
than those offered by DEWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DEWALT, recommended
accessories should be used with this
product.
WARNING: Accessories must be rated
for at least the speed recom mended on
the tool warning label. Wheels and other
accessories running over their rated
accessory speed may fly apart and
cause injury. Threaded accessories
must have a M14 hub. Every
unthreaded accessory must have a
22.2 mm (7/8") arbor hole. If it does not,
it may have been designed for a circular
saw. Accessory ratings must always
be above tool speed as shown on tool
nameplate.
… 51 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DC 411 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC 411 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 4,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info