79272

DeWalt DC 411 Manual

47
Zoom out
Zoom in
Previous page
1/220
Next page
ENGLISH
45
• Only fit 13 Amperes BS1363A approved
plugs fitted with the correctly rated fuse
(1).
• The cable wire colours, or a letter, will be
marked at the connection points of most
good quality plugs. Attach the wires to
their respective points in the plug (see
below). Brown is for Live (L) (2) and Blue
is for Neutral (N) (4).
• Before replacing the top cover of the
mains plug ensure that the cable restraint
(3) is holding the outer sheath of the cable
firmly and that the two leads are correctly
fixed at the terminals crews.
1
2
4
3
WARNING: NEVER use a light socket.
NEVER connect the live (L) or
neutral (N) wires to the earth
pin marked E or .
Using an extension cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see technical data). The minimum conductor size is
1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: Prior to assembly and
adjustment, always remove the battery
pack. Always switch off the tool before
inserting or removing the battery pack.
WARNING: Use only DEWALT battery
packs and chargers.
Inserting and removing the
battery pack into the tool (fi g. 2)
WARNING: To reduce the risk of
serious personal injury, turn tool off
and disconnect battery pack before
making any adjustments or removing/
installing attachments or accessories.
An accidental start-up can cause injury.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the base of the tool with the notch inside
the tool’s handle (fig. 2).
2. Slide the battery pack firmly into the handle until
you hear the lock snap into place.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the release buttons (k) and firmly pull the
battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
Attaching Side Handle
The side handle (e) can be fitted to either side of the
gear case in the threaded holes. Before using the
tool, check that the handle is tightened se cure ly.
To improve user comfort, the gear case will rotate
90˚ for cutting operations.
Rotating the Gear Case (fi g. 4)
WARNING: To reduce the risk of
serious personal injury, turn tool
off and remove battery pack before
making any adjustments or removing/
installing attachments or accessories.
1. Remove the four corner screws attaching the
gear case to motor housing.
2. Without separating the gear case from motor
housing, rotate the gear case head to desired
position.
NOTE: If the gear case and motor housing become
separated by more than 3.17 mm (1/8"), the tool
must be serviced and re-assembled by a DEWALT
service center. Failure to have the tool serviced may
cause brush, motor and bearing failure.
3. Re-install screws to attach the gear case to
the motor housing. Tighten screws to 2.2 Nm
(20 in-lbs.) torque. Overtightening could cause
screws to strip.
Mounting Guard
MOUNTING AND REMOVING GUARD (FIG. 5)
WARNING: To reduce the risk of
serious personal injury, turn tool
off and remove battery pack before
making any adjustments or removing/
installing attachments or accessories.
… 47 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DC 411 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC 411 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 4,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info