546482
30
Zoom out
Zoom in
Previous page
1/132
Next page
ENGLISH
28
Loading the Tool (fi g. 4)
WARNING: Keep the tool pointed
away from yourself and others. Serious
personal injury may result.
WARNING: Never load nails with
the contact trip or trigger activated.
Personal injury may result.
1. Lock OFF trigger.
2. Disconnect the air supply from the tool.
3. Pull the door latch (o) to open the door (p).
4. Rotate the canister door (q) open.
5. Adjust the nail platform (r) to properly
accommodate the nail length being used.
Pull up on the nail platform (r) for shorter nails.
Push in the nail platform adjustment button (
S)
and push down on the nail platform (r) for longer
nails.
6. Place the coil on the nail platform (r).
7. Uncoil enough nails [approximately 3" (8cm)] to
reach the nose of the tool.
8. Insert the first nail into the nose and the
second nail between the two rails of the feed
pawl(t).
NOTE: Be careful not to deform the coil of nails
during the loading process. Otherwise, the nail
guide door will not close and the nails might not
feed consistently.
9. Close the canister door (q) completely.
10. Close the door (p) making sure the door latch
(o) is completely engaged.
Depth Setting (fi g. 5)
WARNING: To reduce risk of serious
injury from accidental actuation when
attempting to adjust depth, ALWAYS:
Lock OFF trigger.
Disconnect air supply.
Avoid contact with trigger during
adjustments.
The depth that the fastener is driven can be adjusted
using the depth adjustment next to the trigger of the
tool.
1. To drive the nail shallower, rotate the depth
setting wheel (g) to the right.
2. To drive a nail deeper, rotate the depth setting
wheel (g) to the left.
Clearing a Jammed Nail (fi g. 4)
If a nail becomes jammed in the nosepiece, keep
the tool pointed away from you and follow these
instructions to clear:
1. Lock OFF trigger.
2. Disconnect the air supply from the tool.
3. Open the door (p).
4. Open the canister door (q).
5. Remove the jammed nail.
6. Correct any deformation that may have
occurred to the nail coil.
NOTE: Should nails continue to jam frequently in
nosepiece, have tool serviced by an authorised
D
EWALT service center.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, lock off trigger, disconnect air
line from tool and remove fasteners
from canister before making
adjustments, or personal injury may
result.
Perform the following maintenance
operations every day:
Lubrication
Lubricate tool with 10 –15 drops of DEWALT
pneumatic tool oil.
Insert drops into the air fitting on the end cap of the
tool.
Drain all condensation from the air
compressor tanks and hoses
Open petcocks or other drain valves on the
compressor tanks.
Allow any accumulated water to drain from
hoses.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D51855 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D51855 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info