548676
13
Zoom out
Zoom in
Previous page
1/32
Next page
ENGLISH
11
support the workpiece securely to
prevent movement of the workpiece
and loss of control. Movement of
the workpiece or loss of control may
create a hazard and cause personal
injury.
Apply only a gentle pressure to the
tool. Do not exert side pressure on the
disc.
Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Install the guard and appropriate disc
or wheel. Do not use excessively worn
discs or wheels.
Be sure the inner and outer flange are
mounted correctly.
Make sure the disc or wheel rotates
in the direction of the arrows on the
accessory and the tool.
Proper Hand Position (fi g. 6)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the side
handle (e), with the other hand on the main handle
(q) of the tool, as shown.
Switching On and Off (fi g. 1)
The on/off switch is equipped with an unlocking
switch.
To run the tool, depress the unlocking switch (b) and
subsequently operate the on/off switch (a).
Release the unlocking switch (b).
To stop the tool, release the switch.
WARNING: Do not switch the tool on
or off when under load.
Lock-on Button (Fig. 1)
For continuous operation depress the lock-on
button (f) and release the on/off trigger switch.
To stop the tool press the on/off switch again.
The lock-on button can be permanently removed
without compromising compliance with regulatory
agencies shown on the tool’s nameplate. Removal
of the lock pin must be done by a DEWALT Service
Center.
Spindle Lock (fi g. 1)
The spindle lock (c) is provided to prevent the
spindle from rotating when installing or removing
wheels. Operate the spindle lock only when the tool
is turned off, unplugged from the power supply, and
has come to a complete stop.
NOTICE: To reduce the risk of damage
to the tool, do not engage the spindle
lock while the tool is operating. Damage
to the tool will result and attached
accessory may spin off possibly
resulting in injury.
To engage the lock, depress the spindle lock button
and rotate the spindle until you are unable to rotate
the spindle further.
Using Flap Discs
WARNING: Metal dust build-up.
Extensive use of flap discs in metal
applications can result in the increased
potential for electric shock. To reduce
this risk, insert an RCD before use
and clean the ventilation slots daily by
blowing dry compressed air into the
ventilation slots inaccordance with the
below maintenance instructions.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off. An accidental start-up can
cause injury.
Pop-off Brushes
The motor will be automatically shut off indicating
that the carbon brushes are nearly worn out and
that the tool needs servicing. The carbon brushes
are not user-serviceable. Take the tool to an
authorised DEWALT repair agent.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D28492 T 5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D28492 T 5 in the language / languages: English, French as an attachment in your email.

The manual is 4,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt D28492 T 5

DeWalt D28492 T 5 User Manual - English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 200 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info