Manual DeWalt D28491 T 3 (page 44 of 200) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

548671

Zoom out

Zoom in

1/200

ENGLISH

WARNING:

• Ensure all materials to be ground or

cut are secured in place.

• Use clamps or a vice to hold

and support the workpiece to a

stable platform. It is important to

clamp and support the workpiece

securely to prevent the movement

of the workpiece and loss of control.

Movement of the workpiece or loss

of control may create a hazard and

cause personal injury.

• Secure the workpiece. A workpiece

clamped with clamping devices or in

a vice is held more secure than by

hand.

• Support panels or any oversized

workpiece to minimize the risk of

wheel pinching and kickback. Large

workpieces tend to sag under their

own weight. Supports must be

placed under the workpiece near the

line of cut and near the edge of the

workpiece on both sides of the wheel.

• Always wear regular working gloves

while operating this tool.

• The gear case becomes very hot

during use.

• Apply only a gentle pressure to the

tool. Do not exert side pressure on the

disc.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition to cool the

accessory. Do not touch accessories

before they have cooled. The discs

become very hot during use.

• Do not use separate reducing

bushings or adapters to adapt large

hole abrasive wheels.

• Never use the tool without the guard

in place.

• The tool is not designed to be used

with a grinding cup.

• Do not use the power tool with a cut-

off stand.

• Never use blotters together with

bonded abrasive products.

• Be aware, the wheel continues to

rotate after the tools is switched off.

Proper Hand Position (ﬁ g. 6)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the side

handle (e), with the other hand on the main handle

(q) of the tool, as shown.

Switching On and Off (ﬁ g. 1)

The on/off switch is equipped with an unlocking

switch.

To run the tool, depress the unlocking switch (b) and

subsequently operate the on/off switch (a).

Release the unlocking switch (b).

To stop the tool, release the switch.

WARNING: Do not switch the tool on

or off when under load.

Spindle Lock (ﬁ g. 1)

The spindle lock (c) is provided to prevent the

spindle from rotating when installing or removing

wheels. Operate the spindle lock only when the tool

is turned off, unplugged from the power supply, and

has come to a complete stop.

NOTICE: To reduce the risk of damage

to the tool, do not engage the spindle

lock while the tool is operating. Damage

to the tool will result and attached

accessory may spin off possibly

resulting in injury.

To engage the lock, depress the spindle lock button

and rotate the spindle until you are unable to rotate

the spindle further.

Using Flap Discs

WARNING: Metal dust build-up.

Extensive use of flap discs in metal

applications can result in the increased

potential for electric shock. To reduce

this risk, insert an RCD before use

and clean the ventilation slots daily by

blowing dry compressed air into the

ventilation slots inaccordance with the

below maintenance instructions.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D28491 T 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 30,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt D28491 T 3

DeWalt D28491 T 3 Additional guide - Polish - 24 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D28491 T 3 Manual

Product: