Manual DeWalt D28423C T 2 (page 26 of 100) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

548665

Zoom out

Zoom in

1/100

ENGLISH

• Fit the inner ﬂ ange (10) correctly onto the spindle

(11) (ﬁ g. C1).

• Place the disc (12) on the ﬂ ange (10) (ﬁ g. C2).

When ﬁ tting a disc with a raised center, make

sure that the raised centre (13) is facing the

ﬂ ange (10).

• Screw the outer ﬂ ange (14) onto the spindle (11)

(ﬁ g. C3):

- the ring on the ﬂ ange (14) must face towards

the disc when ﬁ tting a grinding disc (A);

- the ring on the ﬂ ange (14) must face away from

the disc when ﬁ tting a cutting disc (B).

• Press the spindle lock (3) and rotate the spindle

(11) until it locks in position (ﬁ g. C2)

• Tighten the ﬂ ange (14) with the two-pin spanner

supplied.

• Release the spindle lock.

• To remove the disc, loosen the ﬂ ange (14) with

the two-pin spanner.

Do not use a damaged disc.

Mounting the side handle (ﬁ g. D1 & D2)

• For grinding, screw the side handle (5) tightly into

one of the holes (15) on either side of the gear

case (ﬁ g. D1).

• For cutting, screw the side handle (5) tightly into

the top hole (16) or into one of the holes (17) on

either side of the gear case (ﬁ g. D2).

D28423/D28432C - Rotating the main handle

(ﬁ g. E1 & E2)

The rotary handle facilitates a more comfortable

handling in cutting applications with the side handle

mounted in the top hole.

The rotary handle has locations at 30°, 60° and 90°

both left and right.

• Pull the spring-loaded tab (18) to unlock the

rotary mechanism (ﬁ g. E1). Hold the tab in the

pulled-out position.

• Rotate the handle (19) into the desired position

(ﬁ g. E2).

• Release the tab and lock it in position.

• Check that the rotary mechanism is locked.

Do not use the tool unless the rotary

handle is in the locked postion.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Ensure all materials to be ground or cut

are secured in place.

• Apply only a gentle pressure to the tool.

Do not exert side pressure on the disc.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

Prior to operation:

• Install the guard and appropriate disc or wheel.

Do not use excessively worn discs or wheels.

• Be sure the inner and outer ﬂ ange are mounted

correctly.

• Make sure the disc or wheel rotates in the direction

of the arrows on the accessory and the tool.

Switching on and off (ﬁ g. A)

The on/off switch is equipped with an unlocking

switch or a locking switch for continuous operation.

On/off switch (1) with locking switch (2)

• To run the tool, depress the locking switch (2)

and subsequently operate the on/off switch (1).

• Release the locking switch (2).

• To stop the tool, press the on/off switch again.

On/off switch (1) with unlocking switch (2)

(France only)

• To run the tool, depress the unlocking switch (2)

and subsequently operate the on/off switch (1).

• Release the unlocking switch (2).

• To stop the tool, release the switch.

Do not switch the tool on or off when

under load.

Consult your dealer for further information on the

appropriate accessories.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D28423C T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt D28423C T 2

DeWalt D28423C T 2 Additional guide - English - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D28423C T 2 Manual

Product: