548630

DeWalt D28401 T 2 Manual

23
Zoom out
Zoom in
Previous page
1/88
Next page
23
ENGLISH
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0-2.0 66 66 610
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Mounting and removing the guard (fig. B)
• Place the angle grinder on a table, spindle up.
• Release the clamping lock (6) and hold the guard
(4) over the tool as shown.
• Align the lugs (7) with the notches (8).
• Press the guard down and rotate it to the
required posiiton.
• If required, increase the clamping force by
tightening the screw (9).
• Tighten the clamping lock.
• To remove the guard, release the clamping lock.
Never use the tool without the guard in
place.
Fitting and removing a grinding or cutting disc
(fig. C1 - C3)
• Place the tool on a table, guard up.
• Fit the inner flange (10) correctly onto the spindle
(11) (fig. C1).
• Place the disc (12) on the flange (10) (fig. C2).
When fitting a disc with a raised center, make
sure that the raised centre (13) is facing the
flange (10).
• Screw the outer flange (14) onto the spindle (11)
(fig. C3):
- the ring on the flange (14) must face towards
the disc when fitting a grinding disc (A);
- the ring on the flange (14) must face away from
the disc when fitting a cutting disc (B).
• Press the spindle lock (3) and rotate the spindle
(11) until it locks in position (fig. C2)
• Tighten the flange (14) with the two-pin spanner
supplied.
• Release the spindle lock.
• To remove the disc, loosen the flange (14) with
the two-pin spanner.
Do not use a damaged disc.
Fitting a wire cup brush
• Screw the wire cup brush directly onto the
spindle without the use of the spacer and
threaded flange.
Mounting the side handle (fig. D1 & D2)
• For grinding, screw the side handle (5) tightly into
one of the holes (15) on either side of the gear
case (fig. D1).
• For cutting, screw the side handle (5) tightly into
the top hole (16) or into one of the holes (17) on
either side of the gear case (fig. D2).
Instructions for use
• Always observe the safety instructions
and applicable regulations.
• Ensure all materials to be ground or cut
are secured in place.
• Apply only a gentle pressure to the tool.
Do not exert side pressure on the disc.
• Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Prior to operation:
• Install the guard and appropriate disc or wheel.
Do not use excessively worn discs or wheels.
• Be sure the inner and outer flange are mounted
correctly.
• Make sure the disc or wheel rotates in the direction
of the arrows on the accessory and the tool.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D28401 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D28401 T 2 in the language / languages: Polish as an attachment in your email.

The manual is 0,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt D28401 T 2

DeWalt D28401 T 2 User Manual - English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian, Finnish - 174 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info