447185

DeWalt D2819 Manual

21
Zoom out
Zoom in
Previous page
1/92
Next page
21
ENGLISH
Warning! The use of any accessory or attachment
or performance of any operation with this tool
other than those recommended in this instruction
manual may present a risk of personalinjury.
14 Check for damaged parts
Before use, carefully check the tool and mains
cable for damage. Check for misalignment and
seizure of moving parts, breakage of parts,
damage to guards and switches and any other
conditions that may affect its operation.
Ensure that the tool will operate properly and
perform its intended function. Do not use the tool
if any part is damaged or defective. Do not use
the tool if the switch does not turn it on and off.
Have any damaged or defective parts replaced
by an authorised DEWALT repair agent. Never
attempt any repairs yourself.
15 Unplug tool
Switch off and wait for the tool to come to a
complete standstill before leaving it unattended.
Unplug the tool when not in use, before changing
any parts of the tools, accessories or
attachments and before servicing.
16 Avoid unintentional starting
Do not carry the tool with a finger on the switch.
Be sure that the tool is switched off before
plugging in.
17 Do not abuse cord
Never carry the tool by its cord. Never pull the
cord to disconnect from the socket. Keep the
cord away from heat, oil and sharp edges.
18 Store idle tools
When not in use, tools must be stored in a dry place
and locked up securely, out of reach of children.
19 Maintain tools with care
Keep the tools in good condition and clean for
better and safer performance. Follow the
instructions for maintenance and changing
accessories. Keep all handles and switches dry,
clean and free from oil and grease.
20 Repairs
This tool is in accordance with the relevant safety
regulations. Have your tool repaired by an
authorised DEWALT repair agent. Repairs should
only be carried out by qualified persons using
original spare parts; otherwise this may result in
considerable danger to the user.
Additional safety rules for grinders
• Your grinder has been designed for grinding and
cutting masonry and steel.
Do not cut or grind light metal with a
magnesium content exceeding 80%
since this type of metal is flammable.
• Do not use any accessories other than fibre
reinforced grinding and cutting discs.
• Use the grinding and cutting discs recommended
by the manufacturer only.
• The max. allowable speed of the grinding wheel
or cutting disc must always be equal to or
greater than the no-load speed of the tool
specified on the nameplate.
• Do not cut workpieces requiring a maximum
depth of cut exceeding that of the cutting disc.
• Do not use grinding and cutting discs that do not
conform to the dimensions stated in the technical
data. Do not use any spacers to make a disc fit
onto the spindle.
• Inspect grinding and cutting discs before each
use. Do not use chipped, cracked or otherwise
defective discs.
• If provided, ensure that blotters are used when
the disc is fitted onto the spindle.
• When applying a threaded hole disc, ensure that
the thread is long enough to accept the spindle.
• Ensure that the grinding or cutting disc is
mounted correctly before use.
• Let the tool run at no-load in a safe position for at
least 30 seconds. If there is a considerable
vibration or if any other defect occurs, stop the
tool and check it to determine the cause.
• Do not operate this tool without the guard in place.
• Check that the workpiece is properly supported.
• Do not operate the tool near flammable liquids,
gases or dust. Sparks or hot chips from cutting
or arcing motor brushes may ignite combustible
materials.
• Do not operate the tool while standing in line with
the disc. Keep other persons away from the work
area.
• Do not use cutting discs for side grinding.
• Do not operate the spindle lock while the tool is
running.
• Beware that after switching off the tool the wheel
continues to rotate for a short period.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D2819 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D2819 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 0,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info