Manual DeWalt D28143 T 3 (page 40 of 188) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

547337

Zoom out

Zoom in

1/188

ENGLISH

a. The ring on the threaded clamp nut (h) must

face towards the disc when fitting a grinding

disc (fig. 5A);

b. The ring on the threaded clamp nut (h) must

face away from the disc when fitting a cutting

disc (fig. 5B).

5. Press the spindle lock button (c) and rotate the

spindle (o) until it locks in position.

6. Tighten the threaded clamp nut (h) with the two-

pin spanner supplied.

7. Release the spindle lock.

8. To remove the disc, loosen the threaded clamp

nut (h) with the two-pin spanner.

Fitting and Removing a

Backing Pad/Sanding Sheet (ﬁ g. 1, 5)

1. Place the tool on a table, guard up.

2. Remove the backing flange (i).

3. Place the rubber backing pad correctly onto the

spindle (o).

4. Place the sanding sheet on the rubber backing

pad.

5. Screw the threaded clamp nut (h) onto the

spindle. The ring on the threaded clamp nut (h)

must face towards the rubber backing pad.

6. Press the spindle lock button (c) and rotate the

spindle (o) until it locks in position.

7. Tighten the threaded clamp nut (h) with the two-

pin spanner.

8. Release the spindle lock

9. To remove the rubber backing pad, loosen the

threaded clamp nut (h) wih the two-pin spanner.

Fitting a Wire Cup Brush

Screw the wire cup brush directly onto the spindle

without the use of the spacer and threaded flange.

Prior to Operation

• Install the guard and appropriate disc or wheel.

Do not use excessively worn discs or wheels.

• Be sure the inner and outer flange are mounted

correctly.

• Make sure the disc or wheel rotates in the

direction of the arrows on the accessory and

the tool.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off.

WARNING:

• Ensure all materials to be ground or

cut are secured in place.

• Use clamps or a vice to hold

and support the workpiece to a

stable platform. It is important to

clamp and support the workpiece

securely to prevent the movement

of the workpiece and loss of control.

Movement of the workpiece or loss

of control may create a hazard and

cause personal injury.

• Always wear regular working gloves

while operating this tool.

• The gear case becomes very hot

during use.

• Apply only a gentle pressure to the

tool. Do not exert side pressure on the

disc.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

Proper Hand Position (ﬁ g. 1, 6)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the side

handle (f), with the other hand on the body of the

tool, as shown in figure 6.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D28143 T 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 25,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D28143 T 3 Manual

Product: