546958

DeWalt D28132C T 1 Manual

32
Zoom out
Zoom in
Previous page
1/132
Next page
30
When using a cable reel, always unwind the cable
completely.
Also refer to the table below.
Conductor size (mm
2
) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0 - 2.0 6 6 6 6 6 10
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Assembly and adjustment
WARNING: Prior to assembly and
adjustment always unplug the tool.
MOUNTING AND REMOVING THE GUARD (FIG. B1 & B2)
D28111/D28139 - GUARD WITH FIXING SCREW (FIG. B1)
• Place the angle grinder on a table, spindle up.
• Align the lugs (5) with the notches (6).
• Press the guard down and rotate it to the
required position.
• Securely tighten the screw (7).
• To remove the guard, slacken the screw.
WARNING: Never use the tool without
the guard in place.
D28113(K)/D28130/D28132C/D28134/D28135(K)/D28141 -
KEYLESS GUARD (FIG. B2)
• Place the angle grinder on a table, spindle up.
• Release the clamping lock (8) and hold the guard
(3) over the tool as shown.
• Align the lugs (5) with the notches (6).
• Press the guard down and rotate it to the
required position.
• If required, increase the clamping force by
tightening the screw (9).
• Tighten the clamping lock.
• To remove the guard, release the clamping lock.
WARNING: Never use the tool without
the guard in place.
FITTING AND REMOVING A GRINDING OR CUTTING DISC
(FIG. C1 & C2)
• Place the tool on a table, guard up.
• Fit the inner fl ange (10) correctly onto the spindle
(11) (fi g. C1).
• Place the disc (12) on the fl ange (10). When
fi tting a disc with a raised center, make sure that
the raised centre (13) is facing the fl ange (10).
• Screw the outer fl ange (14) onto the spindle (11)
(fi g. C2):
– the ring on the fl ange (14) must face towards
the disc when fi tting a grinding disc (A);
– the ring on the fl ange (14) must face away from
the disc when fi tting a cutting disc (B).
• Press the spindle lock (2) and rotate the spindle
(11) until it locks in position.
• Tighten the fl ange (14) with the two-pin spanner
supplied.
• Release the spindle lock.
• To remove the disc, loosen the fl ange (14) with
the two-pin spanner.
WARNING: Do not use a damaged disc.
MOUNTING THE SIDE HANDLE (FIG. D)
• Screw the side handle (4) tightly into one of the
holes (14) on either side of the gear case.
Instructions for use
WARNING:
• Always observe the safety instructions
and applicable regulations.
• Ensure all materials to be ground or cut
are secured in place.
ENGLISH
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D28132C T 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D28132C T 1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info