Manual DeWalt D28116 T 2 (page 30 of 124) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546937

Zoom out

Zoom in

1/124

ENGLISH

D28117/D28137

• Remove the fasteners (10).

• Proceed as described above to slide the guard

past the spindle.

• Replace the fasteners.

• Clamp the guard as described above.

Never use the tool without the guard in

place.

Fitting and removing a grinding or cutting disc

(fig. C1 & C2)

• Place the tool on a table, guard up.

• Fit the inner flange (11) correctly onto the spindle

(12) (fig. C1).

• Place the disc (13) on the flange (11). When

fitting a disc with a raised center, make sure that

the raised centre (14) is facing the flange (11).

• Screw the outer flange (15) onto the spindle (12)

(fig. C2):

– the ring on the flange (15) must face towards

the disc when fitting a grinding disc (A);

– the ring on the flange (15) must face away from

the disc when fitting a cutting disc (B).

• Press the spindle lock (2) and rotate the spindle

(12) until it locks in position.

• Tighten the flange (15) with the two-pin spanner

supplied.

• Release the spindle lock.

• To remove the disc, loosen the flange (15) with

the two-pin spanner.

Do not use a damaged disc.

Mounting the side handle (fig. D)

• Screw the side handle (4) tightly into one of the

holes (16) on either side of the gear case.

D28116/D28117/D28136/D28137 - Setting the

electronic speed control (fig. E)

• Turn the dial (5) to the desired level. Turn the dial

upwards for higher speed and downwards for

lower speed. The required setting is a matter of

experience. E.g.:

– when cutting in soft, brittle materials, set the

dial to a low setting;

– when cutting in harder materials, set the dial to

a high setting.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Ensure all materials to be ground or cut

are secured in place.

• Apply only a gentle pressure to the tool.

Do not exert side pressure on the disc.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

Prior to operation:

• Install the guard and appropriate disc or wheel.

Do not use excessively worn discs or wheels.

• Be sure the inner and outer flange are mounted

correctly.

• Make sure the disc or wheel rotates in the

direction of the arrows on the accessory and the

tool.

Switching on and off (fig. A)

• To run the tool, press the on/off switch (1).

• For continuous operation, press the switch

completely forward.

• To stop the tool, release the switch. To stop the

tool in continuous operation, press on the back

part of the switch.

Do not switch the tool on or off when

under load.

Metal applications

• When using the tool in metal applications, make

sure that a residual current device (RCD) has

been inserted to avoid residual risks caused by

metal swarf.

• If the power supply is shut off by the RCD, take

the tool to authorised DEWALT repair agent.

In extreme working conditions,

conductive dust can accumulate inside

the machine housing when working with

metal. This can result in the protective

insulation in the machine becoming

degraded with a potential risk of an

electrical shock.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D28116 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt D28116 T 2

DeWalt D28116 T 2 Additional guide - Polish - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D28116 T 2 Manual

Product: