546219

DeWalt D27107 T 3 Manual

45
Zoom out
Zoom in
Previous page
1/172
Next page
43
ENGLISH
• Loosen the lock knob (59) of the fi rst leg (15).
• Fold the leg inwards.
• Tighten the lock knob.
• Repeat as for the other legs.
• Turn the machine straight up.
Mounting the wheels (fi g. D)
• Place a wheel (14) onto the axles (60) on each side of the machine.
• Place a fl at washer (61) and a nut (62) onto the threaded end of the axles.
• Tighten the nuts using the spanner supplied.
Assembly for mitre saw mode
Mounting the under-table guard (fi g. E)
The under-table guard (63) is fi tted to the top of the saw bench table.
• Place the two fasteners on the left of the guard into the slots (64) on
the left of the blade slot (65). Turn the plastic screws counterclockwise.
• Place the guard fl at on the table and press the fastener in the slot (66)
on the right of the blade slot. Turn the plastic screw counterclockwise.
• To remove, turn the screws clockwise and remove the guard.
Turning the sawhead and table over (fi g. F1 - F4)
• Hold the saw table (19) with one hand and push the table release lever
(2) to the right (fi g. F1).
• Push the table downwards at the front (fi g. F2) and swing it over
completely until the motor assembly is uppermost and the plate (67)
engages in the table locking device (68) (fi g. F3).
• Push the release lever (69) to the rear whilst holding down the head
until the spring-loaded bearing unit (70) can be lifted out of its seating
(fi g. F4).
• Flip the bearing unit up.
• Holding the head fi rmly, allow the spring pressure to take the head
upwards into its rest position.
Mounting the saw blade (fi g. G1 - G4)
WARNING: To reduce the risk of injury, turn unit off and
disconnect machine from power source before installing
and removing accessories, before adjusting or changing
set-ups or when making repairs. Be sure the trigger switch
is in the OFF position. An accidental start-up can cause injury.
WARNING:
• Always change blades with the machine in mitre saw mode.
• Never depress the spindle lock button while the blade is under
power or coasting.
• Do not cut ferrous metal (containing iron or steel) or masonry or
fibre cement product with this mitre saw.
• The teeth of a new blade are very sharp and can be dangerous.
• Depress the head lock up release lever (9) to release the
lower guard (8), then raise the lower guard as far as possible
(Fig.G1).
• With the lower guard held in the raised position, depress the spindle
lock button (74) with one hand, then use the supplied blade spanner
in the other hand to loosen the left-hand threaded blade locking screw
(73) by turning clockwise.
WARNING! To use the spindle lock, press the button as shown
and rotate the spindle by hand until you feel the lock engage.
• Continue to hold the lock button in to keep the spindle from turning
(74, fig.G1).
• Remove the blade locking screw (73) and the outside arbor collar (75).
• Install the saw blade (76) onto the shoulder (77) provided on the
inside arbor collar (78), making sure that the teeth at the bottom edge
of the blade are pointing toward the back of the saw (away from the
operator).
• Replace the outer arbor collar (75).
• Tighten the blade locking screw (73) carefully by turning counter-
clockwise while holding the spindle lock engaged with your other hand.
• Raise the lower guard.
WARNING! Be aware the saw blade shall be replaced in the
described way only. Only use saw blades as specified under
Technical Data; Cat.no.: DT4260 is suggested.
Adjustments for mitre saw mode
Your mitre saw was accurately adjusted at the factory. If readjustment due
to shipping and handling or any other reason is required, follow the steps
below to adjust your saw. Once made, these adjustments should remain
accurate.
Checking and adjusting the blade to the fence (fi g. H1 - H3)
• Loosen the mitre knob (79) and depress the mitre latch (80) to release
the rotating table (5) (fi g. H1).
• Swing the rotating table until the latch locates it at the 0° mitre position.
Do not tighten the knob.
• Pull down the head until the blade just enters the saw kerf (81).
• Place a square (82) against the left side (7) of the fence and blade (76)
(fi g. H2).
WARNING: Do not touch the tips of the blade teeth with the
square.
• If adjustment is required, proceed as follows:
• Loosen the screws (83) (fi g. H3) and move the scale/rotating table
assembly left or right until the blade is at 90° to the fence as measured
with the square (fi g. H2).
• Retighten the screws (83) (fi g. H3). Pay no attention to the reading of
the mitre pointer at this point.
Adjusting the mitre pointer (fi g. H1 & H4)
• Loosen the mitre knob (79) and depress the mitre latch (80) to release
the rotating table (5) (fi g. H1).
• With the mitre knob loose, allow the mitre latch to snap into place as
you rotate the mitre arm past zero.
• Observe the pointer (84) and mitre scale (85) (fi g. H4). If the pointer
does not indicate exactly zero, loosen the screw (86), move the pointer
to read 0° and tighten the screw.
Checking and adjusting the blade to the table (fi g. I1 - I3)
• Loosen the bevel clamp knob (17) (fi g. I1).
• Press the saw head to the right to ensure it is fully vertical and tighten
the bevel clamp knob.
• Pull down the head until the blade just enters the saw kerf (81).
• Place a set square (82) on the table and up against the blade (76) (fi g. I2).
WARNING: Do not touch the tips of the blade teeth with the
square.
• If adjustment is required, proceed as follows:
• Loosen the bevel clamp knob (17) (fi g. I1) and turn the vertical position
adjustment stop screw (87) (fi g. I3) in or out until the blade is at 90° to
the table as measured with the square (fi g. I2).
• If the bevel pointer (88) does not indicate zero on the bevel scale (89),
loosen the screw (90) that secures the pointer and move the pointer as
necessary (fi g. I3).
Adjusting the fence (fi g. J)
The upper part of the left side of the fence can be adjusted to the left to
provide clearance, allowing the saw to bevel to a full 48° left. To adjust the
fence (7):
• Loosen the fence clamping knob (91) and slide the upper part of the
side fence to the left.
• Make a dry run with the saw switched off and check for clearance.
… 45 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D27107 T 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D27107 T 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 15,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info