Manual DeWalt D27107 T 3 (page 42 of 172) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546219

Zoom out

Zoom in

1/172

ENGLISH

• Make sure all locking knobs and clamp handles are tight before starting

any operation.

• Be sure all blade and flanges are clean and the recessed sides of the

collar are against the blade. Tighten the arbor nut securely.

• Use correctly sharpened saw blades. Observe the maximum speed

mark on the saw blade. The marked maximum speed shall always be

higher than the speed marked on rating plate.

• Never operate the saw without the upper and lower guards in place.

• Never place either hand in the blade area when the saw is connected to

the electrical power source.

• Disconnect the saw from the mains before changing blades or carrying

out maintenance.

• Use a push stick at all times, and ensure that you do not place hands

closer than 200 mm from the saw blade while cutting.

• Do not attempt to operate on anything but the designated voltage.

• Do not apply lubricants to the blade when it is running.

• Do not reach around behind the saw blade.

• Always keep the push stick in its place when not in use.

• Do not stand on top of the unit.

• During transportation make sure that the upper part of the saw blade is

covered, e.g. by the guard.

• Do not use the guard for handling or transportation.

• Rebating, slotting or grooving is not allowed.

• Ensure riving knife is adjusted correctly. Never cut without riving knife

assembled.

• Never cut workpiece smaller than 30 mm.

• Without additional support the machine is designed to accept the

maximum workpiece size of:

– Height 81 mm by width 400 mm by length 600 mm

– Longer workpieces need to be supported by suitable additional

table, e.g. D271055 or D271058.

Additional safety rules for ﬂ ip-over saws

• Before using the saw ensure that the machine is stable. Never position

the machine on uneven ground. If needed secure the machine to a

workbench using 100mm long hexagon head bolts instead of bolts (54)

Fig. B.

• Never operate the machine without the guards in position, especially

after a mode change. Keep the guards in good working order and

properly maintained.

• Replace table insert when worn.

• Ensure that the arm is securely fixed in the working position in the

bench sawing mode.

• Ensure that the arm is securely fixed when bevelling in the bench saw

mode.

• Ensure the table is correctly locked when changing the saw mode.

• Never saw ferrous or non-ferrous materials when ripping in the bench

saw mode.

• Before using any accessory consult the instruction manual. The

improper use of an accessory can cause damage.

• Observe the maximum speed marked on the saw blade.

• Use a holder or wear gloves when handling a saw blade.

• Ensure that the blade rotates in the correct direction. Keep the blade

sharp.

• The max. allowable speed of the saw blade must always be equal to or

greater than the no-load speed of the tool specified on the nameplate.

• Do not use saw blades that do not conform to the dimensions stated

in the technical data. Do not use any spacers and spindle rings to

make a blade fit onto the spindle. Use only the blades specified in this

manual, complying with EN 847-1.

• Consider applying specially designed noise-reduction blades.

• Do not use HIGH SPEED STEEL blades.

• Do not use cracked or damaged saw blades.

• After completing the cut, release the switch and wait for the saw blade

to come to a complete stop before returning the head to its upper rest

position.

• Ensure that the arm is securely fixed when performing bevel cuts.

• Do not wedge anything against the fan to hold the motor shaft.

• The blade guard on your saw will automatically raise when the arm is

brought down; it will lower over the blade when the arm is raised.

The guard can be raised by hand when installing or removing saw

blades or for inspection of the saw. Never raise the blade guard

manually unless the saw is switched off.

• Keep the surrounding area of the machine well maintained and free of

loose materials, e.g. chips and cut-offs.

• Check periodically that the motor air slots are clean and free of chips.

• Disconnect the machine from the mains before carrying out any

maintenance work or when changing the blade.

• Use only saw blades specified by the manufacturer. Ensure that the

riving knife is not thicker than the width of the groove cut by the saw

blade and not thinner than the body of the saw blade.

• Make sure the machine is placed on an even surface with sufficient

stability.

• Do not use abrasive or diamond disc.

• In case of an accident or machine failure immediately switch the

machine off and disconnect from power source.

Report the failure and mark the machine in suitable form to prevent

other people from using the defective machine.

• When the saw blade is blocked due to abnormal feed force during

cutting, turn the machine off and disconnect it from power supply.

Remove the workpiece and ensure that the saw blade runs free. Turn

the machine on and start new cutting operation with reduced feed

force.

• Refrain from removing any cut-offs or other parts of the workpiece from

the cutting area while the machine is running and the saw head is not in

the rest position

• Do not use the machine without the legs mounted.

• Make sure your position is always left or right of the cutting line.

• Provide adequate general or localized lighting.

• Ensure the operator is adequately trained in the use, adjustment and

operation of the machine.

• Switch the machine off when unattended.

• Make sure that the LED meets EN 62471. Do not replace the LED

with a different type. If damaged, have the LED light repaired by an

authorized service agent.

• Connect the saw to a dust collection device when sawing wood.

Always consider factors which influence exposure of dust such as:

-– type of material to be machined (chip board produces more dust

than wood);

-– sharpness of the saw blade;

-– correct adjustment of the saw blade,

-– dust extractor with air velocity not less than 20 m/s.

Ensure that the local extraction as well as hoods, baffles and chutes are

properly adjusted.

• Never cut light alloy, especially magnesium.

Residual risks

The following risks are inherent to the use of saws:

- injuries caused by touching the rotating parts.

In spite of the application of the relevant safety regulations and the

implementation of safety devices, certain residual risks cannot be avoided.

These are:

- Impairment of hearing;

- Risk of accidents caused by the uncovered parts of the rotating saw

blade;

- Risk of injury when changing the blade;

- Risk of squeezing fingers when opening the guards;

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D27107 T 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 15,02 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D27107 T 3 Manual

Product: