Manual DeWalt D25830K T 2 (page 28 of 120) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

544666

Zoom out

Zoom in

1/120

ENGLISH

Service Indicator LED (ﬁ g. 2)

The red service indicator LED (c) lights up when

the carbon brushes are nearly worn out to indicate

that the tool needs servicing. After a further 8 hours

of use the motor will automatically be shut off. The

carbon brushes are not user-serviceable. Take the

tool to an authorised D

EWALT repair agent.

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 60745; therefore no

earth wire is required.

WARNING: 115 V units have to

be operated via a fail-safe isolating

transformer with an earth screen

between the primary and secondary

winding.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

DEWALT service organization.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in

the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

Using an Extension Cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

tool (see technical data).

The minimum conductor size is 1.5 mm

. When

using a cable reel, always unwind the cable

completely.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-ups

or when making repairs. Be sure the

trigger switch is in the OFF position. An

accidental start-up can cause injury.

Inserting and Removing SDS Max

Accessories (ﬁ g. 3, 4)

This machine uses SDS Max

chisels (refer to the

inset in figure 4 for a cross-section of an SDS Max

bit shank).

1. Clean and grease the bit shank.

WARNING: Only apply a slight amount

of lubricant to the bit shank. Do not

apply lubricant to the machine.

2. Insert the bit shank into the tool holder (f), and

press and turn the bit slightly until the sleeve

snaps into position.

3. Pull on the bit to check if it is properly locked.

The hammering function requires the bit to be

able to move axially several centimetres when

locked in the tool holder.

4. To remove a bit pull back the tool holder locking

sleeve (f) and pull the bit out of the tool holder.

Indexing the Chisel Position (ﬁ g. 5, 6)

The chisel can be indexed and locked into 8 different

positions.

1. Press the safety lock (e) and rotate the mode

selector (d) until it points rearward. Release the

safety lock.

2. Rotate the chisel in the desired position.

3. Press the safety lock (e) and rotate the mode

selector (d) back to the forward position

indicated by the hammering symbol.

4. Release the safety lock and check that the

mode selector switch is locked in place.

5. Twist the chisel until it locks in position.

Setting the Electronic Speed and

Impact Control Dial (ﬁ g. 2)

Turn the dial (b) to the desired level. The higher the

number, the greater the speed and impact energy.

With dial settings from 1 (low) to 7 (full power) the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D25830K T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 3,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D25830K T 2 Manual

Product: