723580

DeWalt D25553 Manual

7
Zoom out
Zoom in
Previous page
1/36
Next page
ENGLISH
5
12
3
18 D25831
D25501, D25601,
D25603, D25820
3
12
16
Fig. B
SHOCKS Active Vibration Control® System
(Fig. A, F)
D25651, D25601, D25603, D25831,
D25851
For best vibration control, hold the tool with one hand
on the main handle4 and the other hand on the side
handle3. Apply just enough pressure so the damping
device on the main handle is approximately mid stroke. The
hammer only needs enough pressure to engage the active
vibration control. Applying too much pressure will not make
the tool drill or chip faster and active vibration control will
notengage.
Inserting and Removing Spline Drive
Accessories (Fig. C)
D25553, D25651, D25851
WARNING: Burn hazard. ALWAYS wear gloves when
changing bits. Accessible metal parts on the tool and
bits may get extremely hot during operation. Small
bits of broken material may damage barehands.
WARNING: Do not attempt to tighten or loosen drill
bits (or any other accessory) by gripping the front part
of the chuck and turning the tool on. Damage to the
chuck and personal injury mayoccur.
1. Insert the bit shank into the tool holder13 as far as
it will go. The groove on the chisel shank 17  must
be aligned with the symbol 15  on the toolholder. If
inserted correctly, the locking sleeve16 moves back to
the end position and shows a closed locksymbol.
2. Pull on the bit to be sure that it is properlylocked.
3. If the chisel groove is not aligned with the symbol, or
is not inserted to the complete depth the lock symbol
remainsopen.
4. To remove the bit, pull back the locking sleeve and pull
the bitout.
Fig. C 13
17
15
16
Inserting and Removing SDS Max
Accessories (Fig. D)
D25501, D25601, D25603, D25831
1. Pull back the locking sleeve16 and insert the bit shank.
The bit shank must beclean.
2. Turn the bit slightly until the sleeve snaps back
intoposition.
3. Ensure the bit is properlyengaged.
NOTE: The bit needs to move several centimeters in and
out of the tool holder13 when properlyengaged.
4. To remove the bit, pull back the locking sleeve and pull
the bitout.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D25553 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D25553 in the language / languages: English, French, Spanish, All languages as an attachment in your email.

The manual is 2,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info