Manual DeWalt D25501K (page 37 of 160) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544649

Zoom out

Zoom in

1/160

ENGLISH

3. Release the button to lock rod into position.

When drilling with the depth rod, stop when end

of rod reaches surface of material.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

WARNING: Tool bits may be hot and

gloves should be worn when changing

or removing them to avoid personal

injury.

WARNING:

• Be aware of the location of pipework

and wiring.

• Apply only a gentle pressure to the

tool (approximately 20 kg). Excessive

force does not speed up drilling but

decreases tool performance and may

shorten tool life.

• Always hold the tool ﬁrmly with both

hands and ensure a secure stance.

Always operate the tool with the side

handle properly assembled.

NOTE: Operating temperature is -7˚ to +40˚C (19˚

to 104˚ F). Using the tool outside of this temperature

range will decrease the life of the tool.

Proper Hand Position (ﬁ g. 6)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the

side handle (c), with the other hand on the main

handle (d).

Switching On and Off (ﬁ g. 1)

D25501, D25601, D25602, D25603

To turn the tool on, depress the trigger switch (a).

To stop the tool, release the trigger switch.

D25601, D25602, D25603

The lock-on slider (b) allows the trigger switch (a) to

be locked on in chiselling mode only. If the lock-on

button is activated in drilling mode, as a feature the

tool will switch off automatically.

To turn the tool on, press the trigger switch(a).

To stop the tool, release the switch.

For continuous operation, press and hold down the

switch (a), slide the lock-on button (b) upwards and

release the switch.

To stop the tool in continuous operation, press the

switch briefly and release it. Always switch off the

tool when work is finished and before unplugging.

D25820, D25831

To turn the tool on, press the on/off rocker switch (a)

at the lower part of the trigger.

To stop the tool, press the on/off rocker switch at

the upper part of the trigger.

Hammerdrilling

To turn the tool on, press the on/off switch(a).

To stop the tool, release the switch.

Drilling with a Solid Bit (ﬁ g. 1)

D25501, D25601, D25602, D25603

1. Insert the appropriate drill bit.

2. Set the mode selector switch (f) to the

hammerdrilling position.

3. D25601, D25602, D25603 only: Set the

electronic speed and impact control dial(g).

4. Fit and adjust the side handle (c).

5. Mark the spot where the hole is to be drilled.

6. Place the drill bit on the spot and switch on the

tool.

7. Always switch off the tool when work is finished

and before unplugging.

Drilling with a Core Bit (ﬁ g. 1)

1. Insert the appropriate core bit.

2. Assemble the centerdrill into the core bit.

3. Set the mode selector switch (f) to the

hammerdrilling position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D25501K in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D25501K Manual

Product: