Manual DeWalt D25330K (page 19 of 72) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

544662

Zoom out

Zoom in

1/72

ENGLISH

Also refer to the table below.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0-2.0 66 66 610

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment always

unplug the tool.

Inserting and removing SDS-plus

accessories

(fig. B)

This tool uses SDS-plus

accessories (refer to the

inset in fig. B for a cross-section of an SDS-plus

bit

shank).

We recommend to use professional accessories only.

• Clean and grease the bit shank.

• Insert the bit shank into the tool holder (4).

• Push the bit down and turn it slightly until it fits

into the slots.

• Pull on the bit to check if it is properly locked.

The hammering function requires the bit to be

able to move axially several centimetres when

locked in the tool holder.

• To remove a bit pull back the tool holder locking

sleeve (7) and pull out the bit.

Indexing the chisel position (fig. C)

The chisel can be indexed and locked into

12 different positions.

• Insert the chisel as described above.

• Rotate the collar (3) in the direction of the arrow

until the chisel is in the desired position.

Fitting the side handle (fig. D)

The side handle (6) can be fitted to suit both

RH- and LH-users.

Always use the tool with the side handle

properly assembled.

• Loosen the side handle.

• For RH-users, slide the side handle clamp over the

collar behind the tool holder, handle at the left.

• For LH-users, slide the side handle clamp over the

collar behind the tool holder, handle at the right.

• Rotate the side handle to the desired position

and tighten the handle.

Replacing the dust cover (fig. B)

The dust cover (5) prevents dust ingress into the

mechanism. Replace a worn dust cover

immediately.

• Pull back the tool holder locking sleeve (7) and

pull the dust cover (5) off.

• Fit the new dust cover.

• Release the tool holder locking sleeve.

Instructions for use

Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and wiring.

• Apply a pressure of approx. 5 kg to the tool.

Excessive force does not speed up chiselling but

decreases tool performance and may shorten

tool life.

Switching on and off (fig. A & E)

• To run the tool, press the on/off switch (1).

• For continuous operation, press and hold down

the switch (1), slide the lock-on slider (2) into the

lock position and release the switch.

• To stop the tool, release the switch.

• To stop the tool in continuous operation, press

the switch briefly and release it. Always switch off

the tool when work is finished and before

unplugging.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D25330K in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 0,69 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D25330K Manual

Product: