Manual DeWalt D25263 (page 29 of 116) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

712256

Zoom out

Zoom in

1/116

ENGLISH

7. When drilling through a structure thicker than the depth of

the core bit, break away the round cylinder of concrete or

core inside the bit at regular intervals. To avoid unwanted

breaking away of concrete around the hole, ﬁrst drill a hole

the diameter of the center drill completely through the

structure. Then drill the cored hole halfway from eachside.

8. Always switch off the tool when work is ﬁnished and

beforeunplugging.

Rotary Drilling (Fig. A)

1. Hold down the mode selector button

5

then set the mode

selector switch

4

to the “rotary drilling”position.

2. Depending on your tool, follow either of the following

instructions:

- D25032, D25033, D25133, D25143, D25263: Fit the

chuck adapter/chuckassembly.

- D25134, D25144: Replace the

SDS Plus tool holder with the keylesschuck.

3. Proceed as described forhammerdrilling.



WARNING: Never use standard chucks in the

hammerdrillingmode.

Screwdriving (Fig. A)

1. Hold down the mode selector button

5

then set the mode

selector switch

4

to the rotary drillingposition.

2. Select the direction ofrotation.

3. Depending on your tool, follow either of the following

instructions:

- D25032, D25033, D25133, D25143, D25263: Insert

the special SDS Plus screwdriving adaptor for use with

hexagonal screwdriverbits.

- D25134, D25144: Replace the SDS Plus tool holder

with the keyless chuck

4. Insert the appropriate screwdriver bit. When driving slotted

head screws always use bits with a ﬁndersleeve.

5. Gently press the variable speed switch

1

to prevent

damage to the screw head. In reverse (LH) rotation the tool

speed is automatically reduced for easy screwremoval.

6. When the screw is ﬂush with the workpiece, release the

variable speed switch to prevent the screw head from

penetrating into theworkpiece.

Chipping and Chiselling (Fig. A)

D25033, D25133, D25134, D25143,

D25144, D25263

1. Hold down the mode selector button

5

then set the mode

selector switch

4

to the “hammering only”position.

2. Insert the appropriate chisel and rotate it by hand to lock it

intoposition.

3. Adjust the side handle

8

asrequired.

4. Switch on the tool and startworking.

5. Always switch off the tool when work is ﬁnished and

beforeunplugging.



WARNING:

• Do not use this tool to mix or pump easily combustible

or explosive ﬂuids (benzine, alcohol, etc.).

• Do not mix or stir in ﬂammable liquids

labelledaccordingly.

MAINTENANCE

Your

DeWALT

power tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regularcleaning.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. Be sure the

trigger switch is in the OFF position. An accidental start-up

can cause injury.

• This machine is not user-serviceable. Take the tool to an

authorised

DeWALT

repair agent after approximately 40

hours of use. If problems occur before this time contact an

authorised

DeWALT

repairagent.

• The tool will automatically switch off when the carbon

brushes areworn.

Motor Brushes

DeWALT

uses an advanced brush system which automatically

stops the drill when the brushes wear out. This prevents serious

damage to the motor. New brush assemblies are available

at authorised

DeWALT

service centers. Always use identical

replacementparts.

Lubrication

Your power tool requires no additionallubrication.

Accessories and attachments used must be regularly lubricated

around the SDS Plusﬁtment.

Cleaning



WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.



WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D25263 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D25263 Manual

Product: