712253
27
Zoom out
Zoom in
Previous page
1/116
Next page
25
ENGLISH
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with thisproduct.
Torque Limiting Clutch
All rotary hammerdrills are equipped with a torque limiting
clutch that reduces the maximum torque reaction transmitted
to the operator in case of jamming of a drill bit. This feature
also prevents the gearing and electric motor from stalling.
The torque limiting clutch has been factory-set and cannot
beadjusted.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Selecting the Operating Mode
(Fig. B)
The tool can be used in the following operating modes:
Rotary drilling: for screwdriving and for drilling
into steel, wood and plastics
Hammerdrilling: for concrete and masonry
drilling operations.
Bit rotation: non-working position used only to
rotate a flat chisel into the desired position
Hammering only (D25033, D25133, D25134,
D25143, D25144, D25263): for light chipping,
chiselling and demolition applications. In this
mode the tool can also be used as a lever to free
a jammed drillbit.
1. To select the operating mode, press the mode selector
button
5
and rotate the mode selector switch
4
until it
points to the symbol of the requiredmode.
2. Release the mode selector button and check that the mode
selector switch is locked inplace.
WARNING: Do not select the operating mode when the
tool isrunning.
Indexing the Chisel Position (Fig. B)
The chisel can be indexed and locked into differentpositions.
1. Press the mode selector button
5
and rotate the mode
selector switch
4
until it points to the “bit rotation/
hammerdrilling”position.
2. Rotate the chisel to the desiredposition.
3. Set the mode selector switch
4
to the “hammering
only”position.
4. Twist the chisel until it locks inposition.
Inserting and Removing SDS Plus Accessories
(Fig. C)
This tool uses SDS Plus accessories (refer to the inset in Fig.C for
a cross-section of an SDS Plus bit shank). We recommend using
professional accessoriesonly.
1. Clean and grease the bitshank.
2. Insert the bit shank into the SDS Plus tool holder
6
.
3. Push the bit down and turn it slightly until it fits into
theslots.
4. Pull on the bit to check if it is properly locked. The
hammering function requires the bit to be able to move
axially several centimetres when locked in the toolholder.
5. To remove a bit, pull back the tool holder sleeve
10
and
pull out thebit.
WARNING: Always wear gloves when you change
accessories. The exposed metal parts on the tool and
accessory may become extremely hot duringoperation.
Fitting the Side Handle (Fig. D)
The side handle
8
can be fitted to suit both right-handed and
left-handedusers.
WARNING: Do not use the tool without the side handle
properlyassembled.
1. Loosen the sidehandle.
2. For right-handed users: Slide the side handle clamp over
the collar behind the tool holder, handle at theleft.
For left-handed-users: Slide the side handle clamp over
the collar behind the tool holder, handle at theright.
3. Rotate the side handle to the desired position and tighten
thehandle.
Side Handle Work light (Fig. E)
D25144, D25263
The side handle on the D25144 and D25263 has a work
light
15
. The light is battery powered and operated by using
the on/off button
17
.
To replace the worklight’s batteries (CR2032 x 2):
1. Remove battery door screw
16
as shown in FigureE.
2. Replace the battery with the positive face
pointingoutwards.
3. Close the battery compartment and secure thescrew.
Setting the Drilling Depth (Fig. F)
1. Insert the required drill bit as describedabove.
2. Press the depth rod button
9
and keep itdepressed.
3. Fit the depth adjustment rod
7
through the hole in the
depth stopclamp.
4. Adjust the drilling depth asshown.
5. Release the depth stopclamp.
Reversing Lever (Fig. G)
The forward/reverse lever
3
is used to reverse the rotation of
the hammer for backing out fasteners or jammed bits in the
drill-onlyfunction.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D25134 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D25134 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info