Manual DeWalt D25104K (page 27 of 112) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

446419

Zoom out

Zoom in

1/112

ENGLISH

In this mode the tool can also be used as

a lever to free a jammed drill bit.

Bit rotation: non-working position used

only to rotate a flat chisel into the desired

position.

• To select the operating mode, press the safety

lock (5) and rotate the mode selector switch (4)

until it points to the symbol of the required mode.

• Release the safety lock and check that the mode

selector switch is locked in place.

Do not select the operating mode when

the tool is running.

Indexing the chisel position

The chisel can be indexed and locked into 51

different positions.

• Rotate the mode selector switch (4) until it points

to the “bit rotation” position.

• Rotate the chisel in the desired position.

• Set the mode selector switch (4) to the

“hammering only” position.

• Twist the chisel until it locks in position.

Inserting and removing SDS-plus

accessories

(fig. C)

This tool uses SDS-plus

accessories (refer to the

inset in fig. B for a cross-section of an SDS-plus

bit

shank).

We recommend to use professional accessories only.

• Clean and grease the bit shank.

• Insert the bit shank into the tool holder (6).

• Push the bit down and turn it slightly until it fits

into the slots.

• Pull on the bit to check if it is properly locked.

The hammering function requires the bit to be

able to move axially several centimetres when

locked in the tool holder.

• To remove a bit pull back the tool holder locking

sleeve (12) and pull out the bit.

Fitting the side handle (fig. D)

The side handle (10) can be fitted to suit both

RH- and LH-users.

Always use the tool with the side handle

properly assembled.

• Loosen the side handle.

• For RH-users, slide the side handle clamp over the

collar behind the tool holder, handle at the left.

• For LH-users, slide the side handle clamp over

the collar behind the tool holder, handle at the

right.

• Rotate the side handle to the desired position

and tighten the handle.

Setting the drilling depth (fig. E)

• Insert the required drill bit as described above.

• Press the depth stop clamp (11) and keep it

depressed.

• Fit the depth adjustment rod (9) through the hole

in the depth stop clamp.

• Adjust the drilling depth as shown.

• Release the depth stop clamp.

Forward/reverse slider (fig. F1 & F2)

D25102(K)/D25102C/D25103K/D25104K (fig. F1)

• Push the forward/reverse slider (3) to the RH-side

for forward (RH) rotation. See arrows on tool.

• Push the forward/reverse slider (3) to the LH-side

for reverse (LH) rotation.

D25203K (fig. F2)

• Push the forward/reverse slider (3) to the LH-side

for forward (RH) rotation. See arrows on tool.

• Push the forward/reverse slider (3) to the RH-side

for reverse (LH) rotation.

Always wait until the motor has come to

a complete standstill before changing the

direction of rotation.

D25102(K)/D25102C/D25103K/D25203K -

Fitting the chuck adapter & chuck

• Screw the chuck onto the threaded end of the

chuck adapter.

• Insert the connected chuck and adapter in the

tool as though it were a standard SDS-plus

bit.

• To remove the chuck, proceed as for removing a

standard SDS-plus

bit.

Never use standard chucks in the

hammer drilling mode.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D25104K in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D25104K Manual

Product: