Manual DeWalt D24000 T 2 (page 40 of 124) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546603

Zoom out

Zoom in

1/124

ENGLISH

around the machine that allows handling of the workpiece without any

restrictions.

To reduce effects of vibration make sure the environment temperature is

not too cold, machine and accessory is well maintained and the workpiece

size is suitable for this machine.

WARNING:

• Always observe the safety instructions and applicable regulations.

• Check that the machine has been set up securely.

• Check that the workpiece is properly supported.

• Make sure the cutting disc is not contacting the workpiece

before the machine is switched on.

• Allow the motor to reach full speed before cutting.

• Apply only a gentle pressure to the machine. Do not force the

cutting action.

• Keep your hands out of the path of the cutting disc. Do not

place your hands within the marked area as shown in ﬁ g. P.

Prior to operation:

• Install the appropriate cutting disc.

• Make sure all locking knobs and clamp handles are tight.

• Fill the water basin with the sufﬁ cient amount of water for the water

pump to be fully submerged.

Switching on and off (ﬁ g. Q)

• To switch the machine on, set the on/off switch (1) to position I.

• To switch the machine off, set the on/off switch (1) to position 0.

Wired into the mains cable is the residual current device (RCD) containing

the no-volt release switch and the motor overload protector with manual

reset. In case of a power shut-off, proceed as follows:

• Make sure the on/off switch (1) is in the off position.

• Press the reset button on the RCD.

Locking the switch

• In order to avoid unauthorised use of the machine, lock the switch

using a padlock.

Basic saw cuts

General handling

– Try a few simple projects using scrap material until you develop a “feel”

for the machine.

– Always make dry runs (without power) before ﬁ nish cuts so that you

can check the path of the disc.

Vertical straight cross cut (ﬁ g. R)

• Set the bevel angle to 0°.

• Lower the arm to bring the cutting disc in lowest position.

• Place the workpiece ﬂ at on the table and against the fence, with the

ﬁ nished side up. Align the marking on the workpiece with the marking

in the kerf indicator.

• Keep both hands away from the path of the cutting disc.

• Switch the machine on and allow the cutting disc to reach full speed.

Wait until the cutting disc is completely covered with water.

• Slowly feed the workpiece into the cutting disc, keeping it ﬁ rmly

pressed against the fence. Do not force. The cutting disc speed should

be kept constant.

• After completing the cut, switch the machine off, allow the cutting disc

to stop and remove the workpiece.

Bevel cross-cut (ﬁ g. S)

Bevel angles can be set at 22.5° and 45°.

• Loosen the bevel clamp knob (11) and set the bevel as desired.

• Tighten the bevel clamp knob ﬁ rmly.

• Proceed as for a vertical straight cross-cut.

Diagonal cut (ﬁ g. T1 & T2)

The edge guide (5) allows cutting of angles at 45°.

• Place the edge guide with the mounting bracket (72) over the fence.

• Flip the guide fence (73) into position for the required application:

– Flip the fence to the right for cutting small pieces from large tiles.

– Flip the fence to the left for any other application.

• Set the parallel fence to the required distance.

• Tighten the knob (74) to secure the guide in place.

• Proceed as for a vertical straight cross-cut.

Plunge cut (ﬁ g. U)

A plunge cut is used to remove the centre of a tile, e.g. for electrical

outlets, drains, etc.

• Mark the area to be cut on both sides of the tile.

• Fit the appopriate size of cutting disc.

• Adjust the cutting depth to allow the cutting disc to saw only halfway

through the workpiece.

• Place the workpiece ﬂ at on the table and against the fence, with the

ﬁ nished side up. Align the marking on the workpiece with the marking

in the kerf indicator.

• Switch the machine on and allow the cutting disc to reach full speed.

Wait until the cutting disc is completely covered with water.

• Move the table until the marking on the workpiece is underneath the disc.

• Lower the arm to feed the cutting disc into the workpiece. Do not

overcut the mark. As soon as the marking has been cut, lock the arm

into its highest position.

• Repeat as for the other markings.

• Turn the workpiece upside down. Proceed as described above for the

second cuts to meet the ﬁ rst.

• After completing the cut, switch the machine off, allow the cutting disc

to stop and remove the workpiece.

Grooving (ﬁ g. V)

A groove is made into a tile e.g. to accommodate hidden wiring.

• Adjust the cutting depth as required.

• Place the workpiece ﬂ at on the table and against the fence, with the

down side up. Align the marking on the workpiece with the marking in

the kerf indicator.

• Proceed as for a vertical straight cross-cut.

• Repeat the procedure to make a wider groove.

Optional accessories

WARNING: Since accessories, other than those offered by

EWALT, have not been tested with this product, use of such

accessories with this tool could be hazardous. To reduce the

risk of injury, only DEWALT recommended accessories should

be used with this product.

Range of cutting discs available

Type of disc Dimensions (diameter x bore) Usage

DT3733 250 x 25.4 mm Ceramic tile

DT3734 250 x 25.4 mm Porcelain/stone tile

Consult your dealer for further information on the appropriate accessories.

Transporting (ﬁ g. W1 & W2)

The detachable parts can be stored in the water basin for easy transportation.

• Drain the water basin. See “Maintenance”.

• Remove the edge guide and the extension table.

• Lock the sliding table in position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D24000 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D24000 T 2 Manual

Product: