Manual DeWalt D23700 T 2 (page 34 of 140) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546195

Zoom out

Zoom in

1/140

ENGLISH

DO NOT let children come into contact with the

tool. Supervision is required when inexperienced

operators use this tool.

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 60745; therefore no

earth wire is required.

WARNING: 115 V units have to

be operated via a fail-safe isolating

transformer with an earth screen

between the primary and secondary

winding.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

EWALT service organisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in

the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

Using an Extension Cable

If an extension cable is required, use an approved 3–

core extension cable suitable for the power input of

this tool (see technical data).The minimum conductor

size is 1.5 mm

; the maximum length is 30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

Depth of Cut Adjustment (ﬁ g. 1, 2)

1. Loosen the depth adjustment knob (n).

2. Move the shoe (f) to obtain the correct depth of

cut.

3. Tighten the depth adjustment knob (n).

WARNING: For optimal results, allow

the saw blade to protrude from the

workpiece by about 3 mm (see inset in

figure 2).

Bevel Adjustment (ﬁ g. 3)

The bevel angle can be adjusted between 0° and

45°.

1. Loosen the bevel adjustment knob (k).

2. Set the bevel angle by tilting the saw shoe (f)

until the mark indicates the desired angle on the

scale.

3. Tighten the bevel adjustment knob (k).

Shoe Adjustment for 90° Cuts

(ﬁ g. 1, 4)

1. Adjust the saw to 0° bevel.

2. Retract the blade guard using the lever (h) and

place the saw on the blade side.

3. Loosen the bevel adjustment knob (k).

4. Place a square against the blade (j) and shoe (f)

to adjust the 90° setting.

– Slacken the nut (p) of the stop (q).

– Adjust the stop (q) as required.

– Tighten the nut (p) and the adjustment knob

(k).

Replacing the Saw Blade (ﬁ g. 5)

1. Engage the spindle lock button (d) and unscrew

the blade clamping screw (r) by turning

counterclockwise using the hex key supplied

with the tool.

2. Retract the lower blade guard (i) using the

lever (h) and replace the blade (j). Reinstall the

washers (s, t) in the correct position.

3. Check the direction of rotation of the blade.

4. Thread on the blade clamping screw (r) by hand

to hold the washer in position. Turn clockwise.

5. Press the spindle lock button (d) while turning

the spindle until the blade stops rotating.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D23700 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D23700 T 2 Manual

Product: