Manual DeWalt d23551 (page 38 of 160) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

383807

Zoom out

Zoom in

1/160

ENGLISH

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 60745; therefore no

earth wire is required.

WARNING: 115 V units have to

be operated via a fail-safe isolating

transformer with an earth screen

between the primary and secondary

winding.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

DEWALT service organisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in

the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

Using an Extension Cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

tool (see technical data). The minimum conductor

size is 1 mm

; the maximum length is 30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

Depth of Cut Adjustment (ﬁ g. 1, 2)

1. Loosen the depth adjustment knob (q).

2. Move the shoe (f) to obtain the correct depth of

cut.

3. Tighten the depth adjustment knob (q).

WARNING: For optimal results, allow

the saw blade to protrude from the

workpiece by about 5 mm (fig. 2).

Bevel Adjustment (ﬁ g. 1, 3)

The bevel angle can be adjusted between 0° and

the maximum setting.

1. Loosen the bevel adjustment knob (k).

2. Set the bevel angle by tilting the saw shoe (f)

until the mark indicates the desired angle on the

scale.

3. Tighten the bevel adjustment knob (k).

Shoe Adjustment for 90° Cuts (ﬁ g. 1)

1. Adjust the saw to 0° bevel.

2. Retract the blade guard using the lever (h) and

place the saw on the blade side.

3. Loosen the bevel adjustment knob (k).

4. Place a square against the blade and shoe to

adjust the 90° setting.

5. Tighten the bevel adjustment knob (k).

Replacing the Saw Blade (ﬁ g. 1, 4)

1. Engage the blade lock button (d) and unscrew

the blade clamping screw (s) by turning

anticlockwise using the hex wrench supplied

with the tool.

2. Retract the lower blade guard (i) using the

lever (h) and replace the blade (j). Reinstall the

washers (t, u) in the correct position.

3. Check the direction of rotation of the blade.

4. Thread on the blade clamping screw (s) by hand

to hold the washer in position. Turn clockwise.

5. Press the blade lock button (d) while turning the

spindle until the blade stops rotating.

6. Tighten the blade clamping screw firmly using

the wrench.

Adjusting the Riving Knife (ﬁ g. 4)

For the correct adjustment of the riving knife (g),

refer to figure 4. Adjust the clearance of the riving

knife after changing the saw blade or whenever

necessary.

1. Adjust the depth of cut to 0 mm to access the

clamping screws (v) of the riving knife (g).

2. Loosen the screws (v) and pull out the riving

knife to its maximum length.

3. Adjust the clearance and tighten the screws.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt d23551 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt d23551 Manual

Product: