544714

DeWalt D21810 T 2 Manual

30
Zoom out
Zoom in
Previous page
1/132
Next page
28
ENGLISH
● If necessary, press the lock-on button (2) for
continuous operation and release the switch.
The lock-on button works only in full speed,
forward rotation.
● To stop the tool, release the switch.
● To stop the tool in continuous operation, press
the switch briefl y and release it. Always switch
off the tool when work is fi nished and before
unplugging.
Percussion Drilling (fi g. A)
● Select the percussion mode.
● Press the switch (1).
Rotary Drilling (fi g. A)
● Select the rotary drilling mode.
● Press the switch (1).
Screwdriving
● Select forward or reverse rotation.
● Select the rotary drilling mode.
● Press the switch (1).
Drilling
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
WARNING: To reduce the risk of
personal injury, ALWAYS ensure
workpiece is anchored or clamped firmly.
If drilling thin material, use a wood “back-
up” block to prevent damage to the
material.
1. Use sharp drill bits only. For WOOD, use the
low speed setting and twist drill bits, spade bits,
power auger bits, or hole saws. For METAL, use
the low speed setting and steel twist drill bits or
hole saws.
2. Always apply pressure in a straight line with the
bit. Use enough pressure to keep drill biting, but
do not push hard enough to stall the motor or
deflect the bit.
3. Hold tool firmly with both hands to control the
twisting action of the drill.
CAUTION: Drill may stall if overloaded
causing a sudden twist. Always expect
the stall. Grip the drill firmly to control the
twisting action and avoid injury.
4. IF DRILL STALLS, it is usually because it is
being overloaded or improperly used. RELEASE
TRIGGER IMMEDIATELY, remove drill bit
from work, and determine cause of stalling. DO
NOT CLICK TRIGGER ON AND OFF IN AN
ATTEMPT TO START A STALLED DRILL —
THIS CAN DAMAGE THE DRILL.
5. To minimize stalling or breaking through the
material, reduce pressure on drill and ease the bit
through the last fractional part of the hole.
6. Keep the motor running when pulling the bit
back out of a drilled hole. This will help prevent
jamming.
7. With variable speed drills there is no need to
center punch the point to be drilled. Use a
slow speed to start the hole and accelerate by
squeezing the trigger harder when the hole is
deep enough to drill without the bit skipping out.
DRILLING IN METAL
Start drilling with slow speed and increase to full
power while applying firm pressure on the tool. A
smooth even flow of metal chips indicates the proper
drilling rate. Use a cutting lubricant when drilling
metals. The exceptions are cast iron and brass which
should be drilled dry.
NOTE: Large [5/16" (8 mm) to 1/2" (13 mm)] holes in
steel can be made easier if a pilot hole [5/32"
(4 mm) to 3/16" (5 mm)] is drilled first.
DRILLING IN WOOD
Start drilling with slow speed and increase to full
power while applying firm pressure on the tool. Holes
in wood can be made with the same twist drills used
for metal. These bits may overheat unless pulled out
frequently to clear chips from the flutes. Work that is
apt to splinter should be backed up with a block of
wood.
MAINTENANCE
Your D E WALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing
set-ups or when making repairs.
Be sure the trigger switch is in the OFF
position. An accidental start-up can
cause injury.
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D21810 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D21810 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 4,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info