544713
29
Zoom out
Zoom in
Previous page
1/132
Next page
27
ENGLISH
Put the chuck key (10) into each hole in the
side of the chuck and turn clockwise until tight.
To remove the bit, proceed in reverse order.
Fitting the Side Handle ( g. A)
The side handle (6) can be tted to suit both RH-
and LH-users.
WARNING: Always use the drill with the
side handle properly assembled.
Loosen the side handle.
For RH-users, slide the side handle clamp over
the collar behind the chuck, handle at the left.
For LH-users, slide the side handle clamp over
the colar behind the chuck, handle at the right.
Rotate the side handle to the desired position
and tighten the handle.
Setting the Drilling Depth ( g. C)
Insert the required drill bit into the chuck.
Slacken the side handle (6).
Fit the depth adjustment rod (7) through the
hole in the side handle clamp.
Adjust the drilling depth as shown.
Tighten the side handle.
Forward/reverse Slider ( g. A)
To select forward or reverse rotation, use the
forward/reverse-switch (3) (see arrow on tool).
WARNING: Always wait until the motor
has come to a complete standstill
before changing the direction of
rotation.
Two Gear Selector ( g. E)
Your tool is tted with a two gear selector (4) to
vary the speed/torque ratio.
Release the variable speed switch and select
the required position. This can be done either
with the tool switched off or running under no
load condition.
Always align the selector with the arrow on the
gear housing:
1 low speed/high torque
(drilling large holes, driving large screws)
2 high speed/low torque
(drilling smaller holes, drilling in wood)
For information on speed rates, refer to the
technical data.
Do not change gears at full speed or during
use.
Chuck Removal ( g. F, G)
Open the chuck jaws as far as possible.
Insert a screwdriver into the chuck and remove
the chuck retaining screw (12) by turning
clockwise.
Tighten an Allen key into the chuck and strike it
with a hammer as shown.
Prior to Operation
• Insert the appropriate bit.
• Mark the spot where the hole is to be drilled.
OPERATION
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
Be aware of the location of pipework
and wiring.
Apply only a gentle pressure to the tool.
Excessive force does not speed up
drilling but decreases tool performance
and may shorten tool life.
Proper Hand Position (fi g. A, B)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper
hand position as shown.
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the side
handle (6), with the other hand on the main handle
(11).
Switching On and Off ( g. A)
To run the tool, press the variable speed switch
(1). The pressure exerted on the variable speed
switch determines the tool speed.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D21805 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D21805 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 4,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info