544704
27
Zoom out
Zoom in
Previous page
1/120
Next page
25
ENGLISH
trigger switch is in the OFF position. An
accidental start-up can cause injury.
Selecting the Operating Mode (fi g. B)
The tool can be used in two operating modes:
Rotary drilling:
for steel, wood and plastics.
Percussion drilling:
simultaneous rotating and impacting for
concrete and masonry drilling operations.
Select the required operating mode by rotating
the mode selector (4) to the required position.
Inserting and Removing a Bit (fi g. A)
Keyless chuck
Open the chuck by turning the sleeve (9)
counterclockwise and insert the bit shank.
Tighten fi rmly by turning the sleeve clockwise.
Keyed Chuck
Open the chuck by turning the sleeve (9)
counterclockwise and insert the bit shank.
Put the chuck key (10) into each hole in the side
of the chuck and turn clockwise until tight.
To remove the bit, proceed in reverse order.
Fitting the Side Handle (fi g. A)
The side handle (6) can be fi tted to suit both
RH- and LH-users.
WARNING: Always use the drill with the
side handle properly assembled.
Loosen the side handle.
For RH-users, slide the side handle clamp over
the collar behind the chuck, handle at the left.
For LH-users, slide the side handle clamp over
the colar behind the chuck, handle at the right.
Rotate the side handle to the desired position
and tighten the handle.
Setting the Drilling Depth (fi g. C)
Insert the required drill bit into the chuck.
Slacken the side handle (6).
Fit the depth adjustment rod (7) through the hole
in the side handle clamp.
Adjust the drilling depth as shown.
Tighten the side handle.
Forward/reverse Slider (fi g. A)
To select forward or reverse rotation, use the
forward/reverse-switch (3) (see arrow on tool).
WARNING: Always wait until the motor
has come to a complete standstill before
changing the direction of rotation.
Chuck Removal (fi g. E, F)
Open the chuck jaws as far as possible.
Insert a screwdriver into the chuck and remove
the chuck retaining screw (12) by turning
clockwise.
Tighten an Allen key into the chuck and strike it
with a hammer as shown.
Prior to Operation
Insert the appropriate bit.
Mark the spot where the hole is to be drilled.
OPERATION
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
Instructions for Use
WARNING:
Always observe the safety instructions
and applicable regulations.
Be aware of the location of pipework
and wiring.
Apply only a gentle pressure to the tool.
Excessive force does not speed up
drilling but decreases tool performance
and may shorten tool life.
Proper Hand Position (fi g. A, D)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper
hand position as shown.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D21717 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D21717 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 2,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info