Manual DeWalt D21620 (page 30 of 132) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

500468

Zoom out

Zoom in

1/132

ENGLISH

2. Slide the pilot pin through the hole in the center

of the cutter shank.

3. Turn the tool holder locking sleeve (aa)

clockwise and hold it in position.

4. Insert the shank of the accessory (bb) as far into

the tool holder (f) as possible.

5. Release the locking sleeve.

6. Twist the accessory until it locks in position.

7. To remove the accessory, twist the locking

sleeve clockwise and take out the cutter.

Setting the Speed (ﬁ g. 7)

The machine is equipped with a 2-gear selector to

vary the speed/torque ratio.

1. Depress the slider (cc) in order to change the

gear.

– Slide the slider (cc) up for low speed and high

torque (holes from 32 to 50 mm).

– Slide the slider down for high speed and low

torque (holes from 12 to 30 mm).

2. You may have to rotate the tool holder slightly

before the gear engages.

WARNING: Do not change gears at full

speed or during use.

Prior to Operation

Try a few simple projects using scrap material until

you develop a “feel” for the machine.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

• Apply only a gentle pressure to

the tool. Excessive force does not

speed up drilling but decreases tool

performance and may shorten tool life.

• If the accessory jams, stop the motor

and gently raise the accessory out of

the workpiece before resuming work.

• Always use the safety strap.

• Always use the drill guard.

Turning On and Off (ﬁ g. 1, 8)

In order to operate properly, the machine has to

be turned on following the procedure as described

below.

TURNING THE POWER ON AND OFF

Connect the machine to the mains. The power

indicator (dd) will blink.

To turn the power on, press and hold the on/off

button (a) for 1 second. The power indicator will stop

blinking and will remain on.

To turn the power off, press and hold the on/off

button for 1 second. The power indicator will start

blinking until the mains plug is disconnected.

ACTIVATING THE MAGNET

The magnet can only be activated when the power

is turned on.

To turn on the magnet, press the yellow button (b).

The yellow indicator (ee) goes on.

To turn off the magnet, press the yellow button

again. Before releasing, the magnet will remain

engaged for 3 more seconds, which is indicated by

the yellow indicator blinking until it goes off.

TURNING THE DRILL MOTOR ON AND OFF

The drill motor can only be switched on when the

magnet is activated.

To turn the drill motor on, press the green button (c).

The green indicator (ff) goes on.

To turn the drill motor off, press the green button

again. The indicator goes off.

RE-SETTING THE MACHINE

If the power is interrupted during use, or if at any

point the magnetic seal is broken, the machine must

be reset.

1. Turn off the drill motor first, and then the

magnet.

2. Ensure that the work area is clean.

3. Turn on the power.

4. Activate the magnet.

Drilling a Hole (ﬁ g. 1)

1. Always apply an appropriate cutting

fluid/ coolant on the cutting area.

2. Lower the guard (g) so that it screens the

surface to be drilled.

3. Make sure the drill point or cutter pilot is

properly installed over the spot to be drilled.

4. Turn on the drill motor.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D21620 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D21620 Manual

Product: