544691
27
Zoom out
Zoom in
Previous page
1/92
Next page
27
E N G L I S H
● Turn the stabilizer bolts (15) one by one until
the stand is level
Mounting the water collection ring (fig. H)
If the stand is used in wet drilling applications,
a water collection ring can be mounted to ensure
a proper discharge of water.
● Loosen the bolts (46) a few turns.
● Hold the water collection ring (26) in front of the
base (9).
● Slide the recessed ends of the mounting
bracket (47) in the space created between the
bolts and the base.
● Check that the assembly aligns with the
accessory fitted.
● Securely tighten the bolts.
Adjusting the drill angle (fig. I)
The column can be tilted to facilitate slope drilling
applications. The scale (7) represents angles up to
45°.
● Remove the locking bolt (48) and store it in
a safe place.
● Loosen the angle adjustment lever (8).
● Tilt the column at the handle (3).
● Align the top of the lever base with the required
angle (see indication X).
● Tighten the angle adjustment lever.
● After use, restore the stand in straight-up
position and replace the locking bolt.
Fitting the feed handle (fig. J)
The quick-release feed handle (4) can be mounted
in one simple operation both to the left and the
right of the stand.
● Align the locating rod in the feed handle with
the slot in the shaft (49).
● Push the handle onto the shaft.
Adjusting the friction (fig. A)
The friction knob (13) is used to increase or
decrease the friction of the carriage mechanism.
● Turn the knob clockwise to increase the friction.
● Turn the knob counterclockwise to decrease the
friction.
Instructions for use
@
Always observe the safety instructions
and applicable regulations.
+
Also refer to your drill manual.
Prior to operation:
● Make sure the stand is fastened securely.
● Mount the appropriate accessory.
● Check the friction on the carriage.
● Mark the spot where the hole is to be drilled.
Unlocking the carriage (fig. K)
● To unlock the carriage (1) pull out the lock knob
(2).
● To lock the carriage move the carriage until the
locking shaft passes the hole (50) in the column
and jumps into place.
@
Always lock the carriage when the
assembly is not in use.
General tips for drilling with diamond core bits
+
Follow the core bit or manufacturer's
recommendations for using the
accessory.
Note: The use of a centredrill is not necessary.
● Take hold of the feed handle.
● Unlock the carriage.
● Switch on the drill motor in continuous mode.
● Slowly feed the accessory into the workpiece
using the feed handle.
● At the start of the cut, apply light pressure to
allow the accessory to perform the initial groove.
● Continue applying sufficient pressure to achieve
a smooth progressive cut. Do not force.
● Take extra care when the accessory is about to
break through the surface to prevent splintering.
● Always switch off the tool when work is finished
and before unplugging.
● After use move the carriage upwards until the
carriage locks into place.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D215851 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D215851 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info