Manual DeWalt D21583K (page 41 of 172) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544690

Zoom out

Zoom in

1/172

ENGLISH

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

Instructions for Use

WARNING:

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework

and wiring.

• Apply only a gentle pressure to

the tool. Excessive force does not

speed up drilling but decreases tool

performance and may shorten tool life.

• To reduce effects of vibration make

sure the environment temperature is

not too cold, machine and accessory

is well maintained and the workpiece

size is suitable for this machine.

Proper Hand Position (ﬁ g. 1, 7)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the side

handle (e), with the other hand on the main handle (h).

Switching On and Off (ﬁ g. 1)

To run the tool, press the variable speed switch (a).

The pressure exerted on the variable speed switch

determines the tool speed.

For continuous operation, press and hold down the

switch (a), press the lock-on button (b) and release

the switch.

To stop the tool, release the switch.

To stop the tool in continuous operation, press the

switch briefly and release it. Always switch off the

tool when work is finished and before unplugging.

General Tips for Drilling with

Diamond Core Bits

WARNING: Follow the core bit or

manufacturer's recommendations for

using the accessory.

WARNING: When using the machine in

handheld applications, we recommend

to assemble a centredrill into the core

bit to locate the periphery of the hole to

be drilled more accurately. When using

the machine in stationary applications,

i.e. on a stand, the use of a centredrill is

not necessary.

1. Assemble the centredrill into the core bit.

The centredrill is mounted into an adaptor fitted

between the spindle of the machine and the

core bit.

2. Place the centredrill on the spot and switch on

the machine.

3. Drill at low speed until the core penetrates the

surface approx. 5–10 mm.

4. Remove and unplug the machine.

5. Remove the centredrill from its holder.

6. Plug the machine in and insert the core bit into

the workpiece.

7. Continue drilling, increasing to full speed and

drill to the desired depth.

WARNING: Do not mix or stir

inflammable liquids labelled accordingly.

Dry Drilling

1. Connect the machine to an appropriate dust

extraction system.

2. Proceed as described above.

Wet Drilling

1. Connect the machine to an appropriate water

supply system.

2. Adjust the water flow as necessary.

3. Proceed as described above.

WARNING:

If any water comes out

of the drainage hole at the gear neck,

stop the work immediately and have

the machine repaired by an authorised

repair agent.

Drill Stand

D21582K

1. Drilling with the stand is only allowed downwards

or horizontally .

2. The stand must be fixed, either by bolts or

vacuum device.

NOTE: When using bolts for the stationary

stand, use either Cat. No.: D212825 for

concrete or D215826 for masonry.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D21583K in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D21583K Manual

Product: