591334

DeWalt D21583K T-2 Manual

37
Zoom out
Zoom in
Previous page
1/156
Next page
35
ENGLISH
2. To increase the flow, turn the tap
counterclockwise.
Connecting to a Dust Extractor
(fi g. 6)
These tools have a standard 1/2" bayonet fitting for
the dust extractor fitting (g).
1. Screw the adaptor (t) onto the fitting (g) and
tighten firmly.
2. Connect an appropriate dust extraction system
to the adaptor.
Prior to Operation
1. Mount the appropriate accessory.
2. Mark the spot where the hole is to be drilled.
OPERATION
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Instructions for Use
WARNING:
• Always observe the safety instructions
and applicable regulations.
• Be aware of the location of pipework
and wiring.
• Apply only a gentle pressure to
the tool. Excessive force does not
speed up drilling but decreases tool
performance and may shorten tool life.
• To reduce effects of vibration make
sure the environment temperature is
not too cold, machine and accessory
is well maintained and the workpiece
size is suitable for this machine.
Proper Hand Position (fi g. 1, 7)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
MOUNTING AND REMOVING AN ACCESSORY (FIG. 4)
This tool uses threaded core bits and adaptors
which thread directly onto the spindle (d).
We recommend to use professional accessories
only.
1. Choose the appropriate core bit for wet or dry
drilling.
2. Follow the core bit or manufacturer’s
recommendations for mounting the accessory.
You may require an adaptor to fit the bit onto
the spindle.
3. Hold the spindle using the open-ended
wrench(o) and tighten the core bit (p) by
rotating clockwise using the open-ended
wrench (q).
WARNING: Make sure the entire
assembly is tight before starting the
operation.
Two Gear Selector (fi g. 1)
The tool is fitted with a two gear selector (f) to vary
the speed/torque ratio.
1. Release the switch and select the required
position after the motor has come to a
complete standstill.
2. Always align the selector with the marks on the
gear housing.
3. Refer to the technical data to choose the
appropriate gear according to the diameter of
the core bit and the material to be drilled.
4. Do not change gears at full speed or during
use.
Connecting to a Water Supply (fi g. 5)
These tools have a standard 1/2" bayonet fitting for
the water supply fitting (g).
1. Screw the adaptor (r) onto the fitting (g) and
tighten firmly.
2. Close the water tap (s).
3. Connect an appropriate water supply system to
the adaptor.
WARNING: Make sure that the
pressure of the water supply is below
the max. pressure as stated in the
technical data.
Regulating the Water Flow (fi g. 5)
The water tap (s) on the water hose can be adjusted
to regulate the flow of cooling water towards the
drill bit.
1. To reduce the flow, turn the tap clockwise.
… 37 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D21583K T-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D21583K T-2 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info