Manual DeWalt D21583K T-2 (page 33 of 156) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

591334

Zoom out

Zoom in

1/156

ENGLISH

• After interrupting the cut, do not switch on

until the core bit can rotate freely.

• Always trigger off the switch to prevent the

machine from accidentally self starting.

Note this procedure especially after the

power supply is interrupted or the plug is

disconnected from the power outlet.

• Mounting the tool onto a stand is

recommended to increase the user comfort

and reduce the risk of injuries.

• In case of jammed core bit disconnect the

machine from the power supply, remove

the reason for the jam before turning on the

machine again.

DRY DRILLING

• Dry drilling is suitable for masonry

(bricks, breeze blocks).

• Always use a suitable dust extractor.

• Always use core bits designed for dry drilling.

• Do not use the machine handheld with core

bits larger than 100 mm.

• Always mount the drill on a stand when

drilling holes larger than 100 mm.

• Wear a dust mask when performing dry cuts.

D21583 - WET DRILLING

• Wet drilling is suitable for stone and concrete.

• Always use a water cooling device and a

water collection system.

• Always use core bits designed for wet drilling.

• The maximum water pressure is 3 bar. Use

a pressure relieve valve in case of a higher

water pressure.

• Use only pure tap water for cooling

purposes.

• Prevent water from entering the motor or

other electrical components. Make sure the

PRCD is not in contact with water.

Safe Operation for Stationary Stands

• A machine incorrectly assembled may

cause a hazardous situation. Carefully fix the

machine into the drill stand and check that

the drill stand holder is secured.

• Fixing the drill stand with vacuum device can

lead to dangerous situations.

• Check the surface where the drill stand shall

be fixed. surface such as irregular (rough) can

significantly reduce the effectiveness of the

suction system. Coated or laminated surface

can be pulled off during work.

• The minimum vacuum level shall not be lower

than 600mbar. Periodically control this value

on the pressure gauge.

• Do not use drill core bits with a diameter

greater than 202 mm at this application.

5) SERVICE

a) Have your power tool serviced by a

qualified repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Additional Speciﬁ c Safety Rules for

Diamond Drills

• Wear ear protectors. Exposure to noise can

cause hearing loss.

• Hold power tools by insulated gripping

surfaces when performing an operation

where the cutting tool may contact hidden

wiring or its own cord. Cutting accessory

contacting a “live” wire may make exposed

metal parts of the tool “live” and shock the

operator.

• Use auxiliary handles supplied with the

tool. Loss of control can cause personal

injury.

• Wear safety goggles or other eye

protection. Drilling operations cause chips to

fly. Flying particles can cause permanent eye

damage.

• Bits, tools and drilling area get hot during

operation. Wear gloves when touching

them.

• Use the diamond drill under constant

supervision.

• Make sure not to cut through electric mains,

gas or water pipes. Use detection systems

prior to drilling.

• Make sure the cutting accessory is fitted

properly.

• Check all screws and tighten securely before

you use the machine.

• When drilling downward, make sure the core

can drop safely without injuring someone

standing beneath.

• Do not perform overhead (upward) drilling

without the use of suitable protection

shielding (water collecting device).

• When drilling handheld, always use the side

handle and hold the machine firmly with both

hands.

• Make sure to stand on a stable surface and

keep body balance at all times for better

control of reaction torque.

• Inspect the machine before every use. Do not

use the machine if there are any defectives

on the mains plug, power cord, trigger switch

or any part of the housing. Have the machine

repaired by an authorized repair agent.

• Do not use the machine in a damp or wet

location.

• Switch off the machine immediately if there is

any leak of water.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D21583K T-2 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D21583K T-2 Manual

Product: