544689

DeWalt D215831 Manual

26
Zoom out
Zoom in
Previous page
1/92
Next page
26
E N G L I S H
17 D215834 Reduction ring
18 D215825 Fastening set for concrete
19 D215826 Fastening set for masonry
20 D215827 Spare dowel for concrete (10 pcs)
21 D215828 Spare dowel for masonry
22 D215837 Vacuum pump
23 D215839 Vacuum kit
24 D215835 Bracing bracket
25 D215832 Water collection ring
26 D215833 Spare seal for water collection
ring (10 pcs)
Assembly and adjustment
+
Also refer to your drill manual.
Mounting the drill (fig. B)
● Remove the side handle from the machine.
● Loosen the bolt (31) using the feed handle (4).
● Mount the machine to the stand.
- For machines with a 60 mm collar: the
machine can be mounted directly to the stand.
- For machines with a 53 mm collar:
The D215834 reduction ring is required to
make the collar of the drill fit in the drill holder.
● Tighten the bolt (31) using the feed handle (4).
@
Always mount your drill firmly to prevent
movement.
Installing the stand (fig. C - G)
The stand can be installed either vertically (fig. C)
or horizontally (fig. D) on a surface such as a floor
or a wall.
@
Always make sure the stand is securely
fastened on the surface.
Mounting the stand with the fastening set
(fig. E1 & E2)
A fastening set is required to secure the stand to
masonry (fig. E1) or concrete (fig. E2) surfaces.
● Locate the stand at the desired position and mark
the location of the mounting hole on the wall.
● Drill a hole at the marked location.
- In concrete: 15 mm diameter by 55 mm deep
- In masonry: 20 mm diameter by 85 mm deep
● Insert the anchor plug (32) into the hole.
● Tighten the anchor (33) into the anchor plug.
● Position the stand over the anchor.
● Place a washer (34) and wingnut (35) onto the
bolt. Securely tighten the wingnut.
Mounting the stand with the bracing bracket
(fig. F)
For a quick set up in indoor applications, a bracing
bracket can be used to secure the stand.
● Position the stand.
● Place the bracket foot (36) against the base (9).
● Move the latch (37) out of the way to depress
the lever (38). Extend the bracket (24) until it
reaches the opposite surface. Release the lever.
● Clamp the bracket in position using the rod (39).
● Insert the pin (40) into the hole closest to the
clamping mechanism.
Mounting the stand with the vacuum pump
(fig. G1 & G2)
If the stand is to be mounted to delicate surfaces,
a vacuum pump can be used to secure the stand.
The vacuum created in the base keeps the stand
securely in position.
@
This application works only if the stand
is mounted to a flat surface (e.g. tile,
vibrated concrete) which is clean and
free of debris and swarf. Otherwise, the
suction may drop, causing the stand to
fall or move.
● Fit the rubber seal (41) in the slot (42) in the
underside of the base.
● Place the vacuum handle (43) over the opening
in the base (9).
● Tighten the screw (44) with the washer (45) into
the handle.
● Position the stand.
● Connect the hose of the vacuum pump to the
connection point (16).
● Switch on the vacuum pump. Keep the pump
switched on as long as the application requires.
Adjusting the stand (fig. A)
● Read one of the air levels to check whether the
stand is level.
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D215831 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D215831 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info