544687
22
Zoom out
Zoom in
Previous page
1/80
Next page
22
E N G L I S H
Assembly and adjustment
+
Also refer to your drill manual.
Mounting the drill (fig. B)
● Remove the side handle from the machine.
● Loosen the screws (31) using an Allen key.
● Mount the machine to the stand.
● Tighten the screws (31).
@
Always mount your drill firmly to prevent
movement.
Installing the stand (fig. C - F)
The stand can be installed either vertically (fig. C)
or horizontally (fig. D) on a surface such as a floor
or a wall.
@
Always make sure the stand is securely
fastened on the surface.
Mounting the stand with the fastening set
(fig. E1 & E2)
A fastening set is required to secure the stand to
masonry (fig. E1) or concrete (fig. E2) surfaces.
● Locate the stand at the desired position and mark
the location of the mounting hole on the wall.
● Drill a hole at the marked location.
- In concrete: 15 mm diameter by 55 mm deep
- In masonry: 20 mm diameter by 85 mm deep
● Insert the anchor plug (32) into the hole.
● Tighten the anchor (33) into the anchor plug.
● Position the stand over the anchor.
● Place a washer (34) and wingnut (35) onto the
bolt. Securely tighten the wingnut.
Mounting the stand with the bracing bracket
(fig. F)
For a quick set up in indoor applications, a bracing
bracket can be used to secure the stand.
● Position the stand.
● Place the bracket foot (36) against the base (9).
● Move the latch (37) out of the way to depress
the lever (38). Extend the bracket (22) until it
reaches the opposite surface. Release the lever.
● Clamp the bracket in position using the rod (39).
● Insert the pin (40) into the hole closest to the
clamping mechanism.
Adjusting the stand (fig. A)
● Read one of the air levels to check whether the
stand is level.
- Air level (7) for vertical applications
- Air level (8) for horizontal applications
● If adjustment is required, proceed as follows:
● Turn the stabilizer bolts (11) one by one until
the stand is level
Mounting the water collection ring (fig. H)
If the stand is used in wet drilling applications,
a water collection ring can be mounted to ensure a
proper discharge of water.
● Loosen the nut on one of the bolts (11) a few
turns.
● Hold the water collection ring (23) in front of the
base (6).
● Slide the recessed end of the mounting bracket
(41) in the space created between the nut and
the base.
● Check that the assembly aligns with the
accessory fitted.
● Securely tighten the nut.
Fitting the feed handle (fig. J)
The quick-release feed handle (3) can be mounted
in one simple operation both to the left and the
right of the stand.
● Align the locating rod in the feed handle with
the slot in the shaft (42).
● Push the handle onto the shaft.
Adjusting the friction (fig. A)
The friction knob (9) is used to increase or
decrease the friction of the carriage mechanism.
● Turn the knob clockwise to increase the friction.
● Turn the knob counterclockwise to decrease the
friction.
Instructions for use
@
Always observe the safety instructions
and applicable regulations.
+
Also refer to your drill manual.
Prior to operation:
● Make sure the stand is fastened securely.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D215821K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D215821K in the language / languages: English as an attachment in your email.

The manual is 1,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info