Manual DeWalt D21580K T-2 (page 41 of 176) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

591330

Zoom out

Zoom in

1/176

ENGLISH

To switch off, proceed in reverse order.

TO TEST THE RCD

O = Test button: the switch must break the circuit

(machine switches off).

WARNING:

• If in the test mode the switch does

not break the circuit, we recommend

that the unit is inspected by an

authorized D

EWALT repair agent.

• It is not permitted to make any

modifications to the machine, in

particular it is not allowed to open

the PRCD or to repair or replace the

cable.

• Never use the PRCD as a main

switch. Always switch the PRCD

under no load condition.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

Fitting the Side Handle (ﬁ g. 3)

The side handle (e) can be fitted to suit both

RH- and LH-users.

WARNING: Always use the tool with

the side handle properly assembled.

1. Twist the side handle to loosen it.

2. For RH-users, slide the side handle clamp over

the collar, handle at the left.

For LH-users, slide the side handle clamp over

the collar, handle at the right.

3. Rotate the side handle to the desired position

and tighten the handle.

Mounting and Removing an

Accessory (ﬁ g. 4)

This tool uses threaded core bits and adaptors

which thread directly onto the spindle (d).

We recommend to use professional accessories

only.

1. Choose the appropriate core bit for wet or dry

drilling.

2. Follow the core bit or manufacturer’s

recommendations for mounting the accessory.

You may require an adaptor to fit the bit onto

the spindle.

3. Hold the spindle using the open-ended wrench (r)

and tighten the core bit (s) by rotating clockwise

using the open-ended wrench (t).

WARNING: Make sure the entire

assembly is tight before starting the

operation.

Two Gear Selector (ﬁ g. 1)

The tool is fitted with a two gear selector (f) to vary

the speed/torque ratio.

1. Release the switch and select the required

position after the motor has come to a

complete standstill.

2. Always align the selector with the marks on the

gear housing.

3. Refer to the technical data to choose the

appropriate gear according to the diameter of

the core bit and the material to be drilled.

4. Do not change gears at full speed or during use.

Connecting to a Water Supply (ﬁ g. 5)

D21582

These tools have a standard 1/8" pipe thread for the

water supply fitting (g).

1. Remove the cap screw (u). Store the cap screw

in a safe place.

2. Screw the male end of the water hose (v) into

the fitting (g) and tighten firmly.

3. Close the water tap (w).

4. Connect the water hose to an appropriate water

supply system.

WARNING:

Make sure that the

pressure of the water supply is below

the max. pressure as stated in the

technical data.

Regulating the Water Flow (ﬁ g. 5)

The water tap (w) on the water hose can be

adjusted to regulate the flow of cooling water

towards the drill bit.

1. To reduce the flow, turn the tap clockwise.

2. To increase the flow, turn the tap

counterclockwise.

Prior to Operation

1. Mount the appropriate accessory.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D21580K T-2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D21580K T-2 Manual

Product: