Manual DeWalt D21441 (page 24 of 104) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

500447

Zoom out

Zoom in

1/104

ENGLISH

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in the

plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made

to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

Using an extension cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

machine (see technical data). The minimum

conductor size is 1.5 mm

. When using a cable

reel, always unwind the cable completely.

Assembly and adjustment

WARNING: Prior to assembly and

adjustment always unplug the tool.

Inserting and removing a bit (ﬁ g. A)

● Open the chuck by turning the sleeve (8)

counterclockwise and insert the bit shank.

● Place the bit in the chuck as far as it will go and

lift slightly before tightening.

● Tighten ﬁ rmly by turning the sleeve clockwise.

● To remove the bit, proceed in reverse order.

Fitting the side handle (ﬁ g. A)

The side handle (5) can be ﬁ tted to suit both RH-

and LH-users.

WARNING: Always use the drill with the

side handle properly assembled.

● Loosen the side handle.

● For RH-users, slide the side handle clamp over

the collar behind the chuck, handle at the left.

● For LH-users, slide the side handle clamp over

the colar behind the chuck, handle at the right.

● Rotate the side handle to the desired position

and tighten the handle.

Setting the drilling depth (ﬁ g. B)

● Insert the required drill bit into the chuck.

● Slacken the side handle (5).

● Fit the depth adjustment rod (6) through the

hole in the side handle clamp.

● Adjust the drilling depth as shown.

● Tighten the side handle.

Forward/reverse slider (ﬁ g. A)

● To select forward or reverse rotation, use the

forward/reverse-switch (3) (see arrow on tool).

WARNING: Always wait until the motor

has come to a complete standstill

before changing the direction of

rotation.

Two gear selector (ﬁ g. C)

Your tool is ﬁ tted with a two gear selector (4) to

vary the speed/torque ratio.

● Release the variable speed switch and select

the required position. This can be done either

with the tool switched off or running under no

load condition. Always align the selector with

the arrow on the gear housing:

1 low speed/high torque

(drilling large holes, driving large screws)

2 high speed/low torque

(drilling smaller holes, drilling in wood)

For speed rates, refer to the technical data.

● Do not change gears at full speed or during use.

Chuck removal (ﬁ g. D & E)

● Open the chuck jaws as far as possible.

● Insert a screwdriver into the chuck and remove

the chuck retaining screw (9) by turning

clockwise.

● Tighten an Allen key into the chuck and strike it

with a hammer as shown.

Instructions for use

WARNING:

● Always observe the safety instructions

and applicable regulations.

● Be aware of the location of pipework

and wiring.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D21441 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,12 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D21441 Manual

Product: