Manual DeWalt D 28492 (page 26 of 105) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

78707

Zoom out

Zoom in

1/105

ENGLISH

Always ensure that the cable clamp is

correctly and securely ﬁ tted to the

sheath of the cable.

Assembly and adjustment

Prior to assembly and adjustment

always unplug the tool.

Mounting and removing the guard (ﬁ g. B)

● Place the angle grinder on a table, spindle up.

● Align the lugs (7) with the notches (8).

● Press the guard (5) down and rotate it to the

required position.

● Securely tighten the screw (9).

● To remove the guard, slacken the screw.

Never use the tool without the guard in

place.

Fitting and removing a grinding or cutting disc

(ﬁ g. C1 & C2)

● Place the tool on a table, guard up.

● Fit the inner ﬂ ange (10) correctly onto the

spindle (11) (ﬁ g. C1).

● Place the disc (12) on the ﬂ ange (10).

When ﬁ tting a disc with a depressed centre,

make sure that the depressed centre (13) is

facing the ﬂ ange (10).

● Screw the outer ﬂ ange (14) onto the spindle (11)

(ﬁ g. C2):

- the ring on the ﬂ ange (14) must face towards

the disc when ﬁ tting a grinding disc (A);

- the ring on the ﬂ ange (14) must face away

from the disc when ﬁ tting a cutting disc (B).

● Press the spindle lock (4) and rotate the spindle

(11) until it locks in position.

● Tighten the ﬂ ange (14) with the two-pin spanner

supplied.

● Release the spindle lock.

● To remove the disc, loosen the ﬂ ange (14) with

the two-pin spanner.

Do not use a damaged disc.

Fitting a wire cup brush

● Screw the wire cup brush directly onto the

spindle without the use of the spacer and

threaded ﬂ ange.

Mounting the side handle (ﬁ g. D)

● Screw the side handle (6) tightly into one of the

holes (15) on either side of the gear case.

Holding the tool (ﬁ g. E)

● Hold the tool as shown.

● For your own safety, always use the

tool with both hands.

● Always wear regular working gloves

while operating this tool.

● Warning: The gear case becomes very

hot during use.

Instructions for use

● Always observe the safety instructions

and applicable regulations.

● Ensure all materials to be ground or cut

are secured in place.

● Apply only a gentle pressure to the tool.

Do not exert side pressure on the

grinding wheel or cutting disc.

● Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

Prior to operation:

● Install the guard and appropriate disc or wheel.

Do not use excessively worn discs or wheels.

● Be sure the inner and outer ﬂ ange are mounted

correctly.

● Make sure the disc or wheel rotates in the

direction of the arrows on the accessory and

the tool.

Switching on and off (ﬁ g. A)

The on/off switch is equipped with an unlocking

switch or a locking switch for continuous operation.

On/off switch (1) with locking switch (2)

● To run the tool, depress the unlocking switch (3)

and subsequently operate the on/off switch (1).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D 28492 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 1,08 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt D 28492

DeWalt D 28492 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 176 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D 28492 Manual

Product: